[PCB_FORUM] Re: rooms and areas (beginner with performance)

 
If your company is paying a million dollars in support, I would think
some of the other users at your company could help you.  You must have
more than just yourself...
 
Pardon me for getting a little grumpy, but we don't get any of that
support money and after 3 or more years or more of your very basic
questions I'd have thought you'd have realized that you NEED training,
not support.  Getting snotty about ot doesn't help your case.
 
-- 
George Patrick
Tektronix, Inc.
Central Engineering, EDS Applications Support
P.O. Box 500, M/S 39-512
Beaverton, OR 97077-0001
* 503-627-5272 (voice)     * 503-627-5587 (fax)
<http://www.tektronix.com/> 
http://www.tektronix.com     <http://www.pcb-designer.com/>
http://www.pcb-designer.com
 
"Off-Grid and Proud of it!"

-----Original Message-----
From: icu-pcb-forum-bounce@xxxxxxxxxxxxx
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of
sjchar3@xxxxxxxxxxxx
Sent: Monday, August 20, 2007 12:10
To: icu-pcb-forum@xxxxxxxxxxxxx
Subject: [PCB_FORUM] Re: rooms and areas (beginner with performance)


Gary, thanks, I'll ask for money to take training..I thought our million
dollars for support would handle questions.
 
Thanks
Sam


-----Original Message-----
From: Macindoe, Gary <Gary.Macindoe@xxxxxxx>
To: icu-pcb-forum@xxxxxxxxxxxxx
Sent: Mon, 20 Aug 2007 11:16 am
Subject: [PCB_FORUM] Re: rooms and areas (beginner with performance)


Dave,
 
I build the Constraint Area into the BGA library part, and assign the
NET_SPACING_TYPE and NET_PHYSICAL_TYPE (= BGA) there also.
That way, it does move with the BGA symbol, even if you modify its
extents.
 
Also, "sjchar3" (name?), it sounds like you need to talk your employer
into some formal training!
 
Good luck!
 
Gary
 
  
Gary E. MacIndoe
PCB Design Engineer
Fort Collins, Colorado
amd.com
gary.macindoe@xxxxxxx

  _____  

From: icu-pcb-forum-bounce@xxxxxxxxxxxxx
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx
<mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx?> ] On Behalf Of Dave Mattice
Sent: Monday, August 20, 2007 11:17 AM
To: icu-pcb-forum@xxxxxxxxxxxxx
Subject: [PCB_FORUM] Re: rooms and areas (beginner with performance)
 
I have always used a Constraint Area for this. And assigned the
appropriate
Spacing and Physical constraint sets. Only trouble is that the
constraint does not follow
The component when moving. You can create a Alternate and lock it in
place that way.
 
dm
 

  _____  

From: icu-pcb-forum-bounce@xxxxxxxxxxxxx
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx
<mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx?> ] On Behalf Of
sjchar3@xxxxxxxxxxxx
Sent: Monday, August 20, 2007 9:21 AM
To: icu-pcb-forum@xxxxxxxxxxxxx
Subject: [PCB_FORUM] rooms and areas (beginner with performance)
 
group: I have a BGA and I would like to route 4 mil trace between pins,
and only a certain via would be used in this location. The rest of the
board is 8 mil traces. Do i set up a room, area or region?  

Thanks Austin for you earlier reply.

Thanks again. 

  _____  

 
<http://pr.atwola.com/promoclk/100122638x1081283466x1074645346/aol?redir
=http%3A%2F%2Fwww%2Eaim%2Ecom%2Ffun%2Fmail%2F> Check Out the new free
AIM(R) Mail -- Unlimited storage and industry-leading spam and email
virus protection.
  _____  

 
<http://pr.atwola.com/promoclk/100122638x1081283466x1074645346/aol?redir
=http%3A%2F%2Fwww%2Eaim%2Ecom%2Ffun%2Fmail%2F> Check Out the new free
AIM(R) Mail -- Unlimited storage and industry-leading spam and email
virus protection.

GIF image

Other related posts: