well you are right. my v14.2 does that now too. I could have sworn it used to work different. losing it, I guess. -----Original Message----- From: Larry Briski [mailto:lgb@xxxxxxx] Sent: Thursday, September 09, 2004 12:00 PM To: icu-pcb-forum@xxxxxxxxxxxxx Subject: [PCB_FORUM] Re: linewidth change Patricki I'm still in 14.2. The line width action you describe occurs in 14.2 also. I've seen it in previous versions of Allegro too. Larry westfeldt wrote: > Thank you David, but that was not it. It was unset, but setting it > had no effect. > > Further details. This effect does not occur if I start route with > some specified width and change layers. It only occurs when I start > routing on an existing trace so that this existing width is my routing width. > When I drop the via, it reverts to the default drc trace width. > > ---------------------------------------------------------------------- > -- > From: David Greig [mailto:David@xxxxxxxxxxxxxx] > Sent: Thursday, September 09, 2004 10:47 AM > To: icu-pcb-forum@xxxxxxxxxxxxx > Subject: [PCB_FORUM] Re: linewidth change > > Is the environment variable acon_no_impedance width unset? This would > let the tool adjust line width to compensaye for impedances on each layer. > > I set it because I don't agree with the Allegro methodology for > calculating impedance. Correct impedance calculations are easy enough > to do (or you can resort to Method Of Moments 2D tools) Either will > give more satisfactory results. > > Another reason for not letting the tool decide is if you want to > identify controlled impedance routes by layer to the fab shop. Just > make sure that your plane fill aperture is different from the > controlled line width or the fab shop will have a harder time of it! > > Best Regards > > David Greig > _________________________________________ > Director > GigaDyne Ltd > Buchan House > Carnegie Campus > Dunfermline KY11 8PL > United Kingdom > Tel. +44 (0) 1383 62 49 75 > _________________________________________ > > > ---------------------------------------------------------------------- > -- > From: westfeldt [mailto:westfeldt_nbcd@xxxxxxxxx] > Sent: 09 September 2004 16:27 > To: icu-pcb-forum@xxxxxxxxxxxxx > Subject: [PCB_FORUM] linewidth change > > Still getting used to v15.1. Sometimes tracewidth goes from my > current width to minimum drc value when I drop a via; didn't do that > in my v14.2. How do I fix this? > > Patrick Westfeldt, Jr. > North Boulder Circuit Design > westfeldt_nbcd@xxxxxxxxx > 720-406-0887 > c 720-272-5822 > > > -- > Virus scanned by Lumison. > > -- Lawrence Briski SGI Chippewa Falls, WI 54729 Phone: 715.726.7440 ----------------------------------------------------------- To subscribe/unsubscribe: Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx with a subject of subscribe or unsubscribe To view the archives of this list please login at //www.freelists.org. Our list name is icu-pcb-forum or go to //www.freelists.org/archives/icu-pcb-forum/ Problems or Questions: Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx Want to post a job listing ? DON'T DO IT HERE! Better yet, join our jobs listing forum. SUBSCRIBE: icu-jobs-forum-subscribe@xxxxxxxxxx POST: icu-jobs-forum@xxxxxxxxxx ----------------------------------------------------------- ----------------------------------------------------------- To subscribe/unsubscribe: Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx with a subject of subscribe or unsubscribe To view the archives of this list please login at //www.freelists.org. Our list name is icu-pcb-forum or go to //www.freelists.org/archives/icu-pcb-forum/ Problems or Questions: Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx Want to post a job listing ? DON'T DO IT HERE! Better yet, join our jobs listing forum. SUBSCRIBE: icu-jobs-forum-subscribe@xxxxxxxxxx POST: icu-jobs-forum@xxxxxxxxxx -----------------------------------------------------------