[PCB_FORUM] Re: finding line numbers

Thank You Carolyn.
I learned how to come up with net names back in the day when 8
characters was considered
enough for any situation. This is what I would have come up with back
then: PX4V3FBB
Shirley in Oregon

________________________________

From: icu-pcb-forum-bounce@xxxxxxxxxxxxx
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of
Carolyn.Schaefer@xxxxxxxxxx
Sent: Thursday, April 27, 2006 11:46 AM
To: icu-pcb-forum@xxxxxxxxxxxxx
Subject: [PCB_FORUM] Re: finding line numbers


Parentheses in netnames will cause problems - the + and . are probably
not good either.  What Shirley suggests is very good.
 
Carolyn


________________________________

        From: icu-pcb-forum-bounce@xxxxxxxxxxxxx
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of Bolman, Shirley
H
        Sent: Thursday, April 27, 2006 11:28 AM
        To: icu-pcb-forum@xxxxxxxxxxxxx
        Subject: [PCB_FORUM] Re: finding line numbers
        
        
        No wonder! I do believe there are some restricted characters.
Someone needs to let the 
        person who did the schematic that he doesn't need to write a
novel when he comes up with
        net names.
        PCIE_X4_P3P3VAUX_FBASEB probably would be better. No special
characters but it
        still describes the signal.
         
        Shirley in Oregon

________________________________

        From: icu-pcb-forum-bounce@xxxxxxxxxxxxx
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of
sjchar3@xxxxxxxxxxxx
        Sent: Thursday, April 27, 2006 9:20 AM
        To: icu-pcb-forum@xxxxxxxxxxxxx
        Subject: [PCB_FORUM] Re: finding line numbers
        
        
        Here is one net name, its choking on (I didn't do the sch)
         
        PCIE_X4_(+)3.3VAUX_FROM_BASE_B 
         
        -----Original Message-----
        From: Bolman, Shirley H <shirley.h.bolman@xxxxxxxxx>
        To: icu-pcb-forum@xxxxxxxxxxxxx
        Sent: Thu, 27 Apr 2006 08:50:21 -0700
        Subject: [PCB_FORUM] Re: finding line numbers
        
        
        The net names don't have any spaces in them by any chance?
        Shirley in Oregon

________________________________

        From: icu-pcb-forum-bounce@xxxxxxxxxxxxx
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of
sjchar3@xxxxxxxxxxxx
        Sent: Thursday, April 27, 2006 6:53 AM
        To: icu-pcb-forum@xxxxxxxxxxxxx
        Subject: [PCB_FORUM] Re: finding line numbers
        
        
        Group: Seems if i shorten net names the line errors jump to
another line. I thought the net names could be up to 32 characters. Is
this true? 
         
        -----Original Message-----
        From: Bolman, Shirley H <shirley.h.bolman@xxxxxxxxx>
        To: icu-pcb-forum@xxxxxxxxxxxxx
        Sent: Wed, 26 Apr 2006 14:26:36 -0700
        Subject: [PCB_FORUM] Re: finding line numbers
        
        
        Be sure you check the previous line or few lines. Most of the
time when it reports an error on line XXX
        it was because the previous line did not have the correct format
i.e. ; :, etc
         
        Shirley in Oregon

________________________________

        From: icu-pcb-forum-bounce@xxxxxxxxxxxxx
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of
sjchar3@xxxxxxxxxxxx
        Sent: Wednesday, April 26, 2006 2:02 PM
        To: icu-pcb-forum@xxxxxxxxxxxxx
        Subject: [PCB_FORUM] Re: finding line numbers
        
        
        Alan
        Thanks, thats even better . Still can tell what kind of error
i'm looking for.
         
        Sam
         
        -----Original Message-----
        From: Ruprecht, Alan P @ DISPLAYS <alan.p.ruprecht@xxxxxxxxxx>
        To: icu-pcb-forum@xxxxxxxxxxxxx
        Sent: Wed, 26 Apr 2006 16:44:16 -0400
        Subject: [PCB_FORUM] Re: finding line numbers
        
        
        If your using OrCad go to File/Open/Text File
         
         
         
        
________________________________

        From: icu-pcb-forum-bounce@xxxxxxxxxxxxx
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of
sjchar3@xxxxxxxxxxxx
        Sent: Wednesday, April 26, 2006 4:02 PM
        To: icu-pcb-forum@xxxxxxxxxxxxx
        Subject: [PCB_FORUM] finding line numbers
         
        Group: I get Error:Line 334 while running netlist. I know I've
done this before, but notepad, wordpad and words do not give me line
numbers. I remember setting up one of the programs to set up goto. Can
someone refresh my memory on this?
         
        Thanks Sam
        
________________________________

        Try the New Netscape Mail Today!
        Virtually Spam-Free | More Storage | Import Your Contact List
        http://mail.netscape.com 
________________________________

        Try the New Netscape Mail Today!
        Virtually Spam-Free | More Storage | Import Your Contact List
        http://mail.netscape.com 
________________________________

        Try the New Netscape Mail Today!
        Virtually Spam-Free | More Storage | Import Your Contact List
        http://mail.netscape.com 
________________________________

        Try the New Netscape Mail Today!
        Virtually Spam-Free | More Storage | Import Your Contact List
        http://mail.netscape.com

Other related posts: