[PCB_FORUM] Re: Turn off strokes

Sorry my mistake that should have been for Allegro PCB Editor
Checking the documentation, I found the following
************************************************************************
******************
Running Commands with Strokes
In the drawing area, place the cursor over an object, or if you are
zooming or panning, over the region you want to view.

Note:  You can draw stroke patterns, such as undo (U) and zoom fit (W),
anywhere in the drawing area, because they do not create a bounding box
or act on a specific object. 

Press Ctrl or SHIFT, hold down the left mouse button and make a stroke.

You can also press Ctrl, hold down the right mouse button and make a
stroke.

Note:  If the Ctrl+LMB Select and Drag check box in the General tab of
the Design Entry Options dialog box is selected, you need not press Ctrl
or SHIFT. You only need to hold down the left mouse button and make a
stroke. 

As you move the mouse, you see the stroke pattern being drawn.

Release the left mouse button when the stroke is complete.

If Design Entry HDL recognizes the stroke, the command runs as though
you typed it into the console window.

Design Entry HDL provides these default strokes (red indicates the
starting point for the stroke pattern):
************************************************************************
******************

-----Original Message-----
From: icu-pcb-forum-bounce@xxxxxxxxxxxxx
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of Gennadiy
Kiryukhin
Sent: Wednesday, December 03, 2008 9:47 PM
To: icu-pcb-forum@xxxxxxxxxxxxx
Subject: [PCB_FORUM] Re: Turn off strokes

I don't have Setup menu in 'Allegro PCB Design HDL 220'
I have 'Setup' button in the Project Manager but I could not find
'User Preferences' there.

ARIES_LUMAGUE@xxxxxxxxxxx wrote:
> Gennadiy,
>>From menu
> Setup --> User Preferences
> Go to 
> Input folder and un check "no_dragpopup" then click OK
> 
> -----Original Message-----
> From: icu-pcb-forum-bounce@xxxxxxxxxxxxx
> [mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of Gennadiy
> Kiryukhin
> Sent: Wednesday, December 03, 2008 2:27 AM
> To: icu-pcb-forum@xxxxxxxxxxxxx
> Subject: [PCB_FORUM] Turn off strokes
> 
> Is there any way to turn off the strokes in Design Entry HDL?
> 
> Thanks,
> Gennadiy
> -----------------------------------------------------------
> To subscribe/unsubscribe: 
> Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx
> with a subject of subscribe or unsubscribe
> 
> To view the archives of this list go to
> http://www.freelists.org/archives/icu-pcb-forum/
> 
> Problems or Questions:
> Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx
> -----------------------------------------------------------
> -----------------------------------------------------------
> To subscribe/unsubscribe: 
> Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx
> with a subject of subscribe or unsubscribe
> 
> To view the archives of this list go to
http://www.freelists.org/archives/icu-pcb-forum/
> 
> Problems or Questions:
> Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx
> -----------------------------------------------------------
> 

-- 

Gennadiy Kiryukhin
Development Engineer
ATSI
8157 US Route 50
Athens, OH 45701
Phone: (740) 592-2874
Fax (740) 594-2875
-----------------------------------------------------------
To subscribe/unsubscribe: 
Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx
with a subject of subscribe or unsubscribe

To view the archives of this list go to
http://www.freelists.org/archives/icu-pcb-forum/

Problems or Questions:
Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx
-----------------------------------------------------------
-----------------------------------------------------------
To subscribe/unsubscribe: 
Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx
with a subject of subscribe or unsubscribe

To view the archives of this list go to 
http://www.freelists.org/archives/icu-pcb-forum/

Problems or Questions:
Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx
-----------------------------------------------------------

Other related posts: