[PCB_FORUM] Re: The router...
- From: rjbzxr@xxxxxxxxxxxx
- To: icu-pcb-forum@xxxxxxxxxxxxx
- Date: Fri, 08 Jul 2005 12:25:44 -0400
OrCAD Layout and Allegro both run from the Specctra Autorouter.
Just that Layout will check out a 6layer router without any advanced rule
options.. but they are the same router.
** I guess you are on about the - Route -> Automatic / Editor options in
Allegro and Layout and NOT the interactive menus..
Tom Robinson <trobinson@xxxxxxxxxx> wrote:
>Hi All:
>
>When Orcad went to windows, they bought NeuroRoute from Gene Marsh in '96?
>Or it was licensed to Orcad and Protel bought it. Gene did good.
>
>That went into Orcad Layout, I think?.
>
>Is any of that NeuroRoute code still in any Orcad/Cadence products?
>
>tr :)
>
>
>-----Original Message-----
>From: Austin Franklin [mailto:austin@xxxxxxxxxxxx]
>Sent: Friday, July 08, 2005 11:53 AM
>To: icu-pcb-forum@xxxxxxxxxxxxx
>Subject: [PCB_FORUM] Re: The router...
>
>
>IMO, the interactive router in Allegro works very well. Differential pairs
>work great. There are different modes for hug preferred, shove etc. I
>don't know all the intricacies of all of them yet, but this interactive
>router is my preferred way of routing a board. It gives you a real time
>report of DPTol and length rules.
>
>I have not compared it to the Specctra interactive router, but perhaps a
>combination of the two would be best.
>
>Regards,
>
>Austin
>
>
>> -----Original Message-----
>> From: icu-pcb-forum-bounce@xxxxxxxxxxxxx
>> [mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx]On Behalf Of
>> george.h.patrick@xxxxxxxxxxxxxx
>> Sent: Friday, July 08, 2005 11:42 AM
>> To: icu-pcb-forum@xxxxxxxxxxxxx
>> Subject: [PCB_FORUM] Re: The router...
>>
>>
>>
>> I think that's the router Tom was talking about :)
>>
>> --
>> George Patrick
>> Tektronix, Inc.
>> Central Engineering, PCB Design Group
>> P.O. Box 500, M/S 39-512
>> Beaverton, OR 97077-0001
>> Phone: 503-627-5272 Fax: 503-627-5587
>> http://www.tektronix.com http://www.pcb-designer.com
>>
>> It's my opinion, not Tektronix'
>>
>>
>>
>> -----Original Message-----
>> From: icu-pcb-forum-bounce@xxxxxxxxxxxxx
>> [mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of Austin Franklin
>> Sent: Friday, July 08, 2005 08:39
>> To: icu-pcb-forum@xxxxxxxxxxxxx
>> Subject: [PCB_FORUM] Re: The router...
>>
>>
>> Hi George,
>>
>> > > The router that is built into Allegro...
>> >
>> > And it's not really "built-in" unless you pay the licensing for it
>> > (what do they call it now, 610?)...
>>
>> The interactive router in Allegro is at least in the Performance
>> version of
>> the 200 series tools. Is that the router you are talking about?
>>
>> Regards,
>>
>> Austin
>
>-----------------------------------------------------------
>To subscribe/unsubscribe:
> Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx
> with a subject of subscribe or unsubscribe
>
>To view the archives of this list please login at
>//www.freelists.org. Our list name is icu-pcb-forum
>or go to //www.freelists.org/archives/icu-pcb-forum/
>
>Problems or Questions:
> Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx
>
>Want to post a job listing ? DON'T DO IT HERE!
>Better yet, join our jobs listing forum.
>
>SUBSCRIBE: icu-jobs-forum-subscribe@xxxxxxxxxx
>POST: icu-jobs-forum@xxxxxxxxxx
>-----------------------------------------------------------
>
>This message and any file transmitted with it may contain confidential
>information and is exempt from disclosure under applicable law. The
>information contained in this message and any file transmitted with it
>is transmitted in this form based on a reasonable expectation of
>privacy. Any disclosure, distribution, copying or use of the
>information by anyone other than the intended recipient, regardless of
>address or routing, is strictly prohibited. If you have received this
>message in error, please advise the sender by immediate reply and delete
>the original message. Personal messages express views solely of the
>sender and are not attributable to Biodex Medical Systems, Inc.
>-----------------------------------------------------------
>To subscribe/unsubscribe:
> Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx
> with a subject of subscribe or unsubscribe
>
>To view the archives of this list please login at
>//www.freelists.org. Our list name is icu-pcb-forum
>or go to //www.freelists.org/archives/icu-pcb-forum/
>
>Problems or Questions:
> Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx
>
>Want to post a job listing ? DON'T DO IT HERE!
>Better yet, join our jobs listing forum.
>
>SUBSCRIBE: icu-jobs-forum-subscribe@xxxxxxxxxx
>POST: icu-jobs-forum@xxxxxxxxxx
>-----------------------------------------------------------
>
__________________________________________________________________
Switch to Netscape Internet Service.
As low as $9.95 a month -- Sign up today at http://isp.netscape.com/register
Netscape. Just the Net You Need.
New! Netscape Toolbar for Internet Explorer
Search from anywhere on the Web and block those annoying pop-ups.
Download now at http://channels.netscape.com/ns/search/install.jsp
-----------------------------------------------------------
To subscribe/unsubscribe:
Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx
with a subject of subscribe or unsubscribe
To view the archives of this list please login at
//www.freelists.org. Our list name is icu-pcb-forum
or go to //www.freelists.org/archives/icu-pcb-forum/
Problems or Questions:
Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx
Want to post a job listing ? DON'T DO IT HERE!
Better yet, join our jobs listing forum.
SUBSCRIBE: icu-jobs-forum-subscribe@xxxxxxxxxx
POST: icu-jobs-forum@xxxxxxxxxx
-----------------------------------------------------------
Other related posts:
