[PCB_FORUM] Re: Question regarding the netlength.il skill file

---

From:  Robert Szumowicz <robert.szumowicz@xxxxxxxxxx>
Reply-To:  icu-pcb-forum@xxxxxxxxxxxxx
To:  icu-pcb-forum@xxxxxxxxxxxxx
Subject:  [PCB_FORUM] Re: Question regarding the netlength.il skill file
Date:  Wed, 07 Feb 2007 20:23:37 +0000
>They do work with Allegro Studio and even with Allegro in orcad demo
>mode (15.7). I think the limitation is that they need to loaded at
>startup.
>
>regards,
>Robert
>
>sjchar3@xxxxxxxxxxxx wrote:
>>I don't think the skill files work with the basic allergro studio
>>tool. You may need to upgrade. I think this is still true.
>>  Sam   -----Original Message-----
>>From: arimitsus@xxxxxxxxxxx
>>To: icu-pcb-forum@xxxxxxxxxxxxx
>>Sent: Wed, 7 Feb 2007 12:28 PM
>>Subject: [PCB_FORUM] Question regarding the netlength.il skill file
>>
>>Hello once again.
>>I was trying to test out the netlength.il skill file but when I
>>load the .il file and run the command (det) it gives me the error
>>below.
>>E- *Error* fprintf: argument #1 should be an I/O port (type
>>template = "ptg") - nil
>>I have tried running it on both Version 14 and 15 and I have had no
>>luck.  Does anyone else get this error?  Has anyone found solution
>>for this?  Please let me know if anyone has had this problem.
>>Thank you,
>>Seiji
>>
>>    
>>------------------------------------------------------------------------
>>     From: /"Soledad Attia" <SAttia@xxxxxxxxxxxxxx
>>     <_javascript_:parent.ComposeTo("SAttia%40printronix.com",
>>"");>>/
>>     Reply-To: /icu-pcb-forum@xxxxxxxxxxxxx
>>     <_javascript_:parent.ComposeTo("icu-pcb-forum%40freelists.org",
>>"");>/
>>     To: /<icu-pcb-forum@xxxxxxxxxxxxx
>>     <_javascript_:parent.ComposeTo("icu-pcb-forum%40freelists.org",
>>"");>>/
>>     Subject: /[PCB_FORUM] Re: Is it possible to down rev from
>>version
>>     15-->14-->13?/
>>     Date: /Wed, 7 Feb 2007 09:04:21 -0800/
>>
>>     Hi Seiji
>>          You can窶冲 go down a version once is saved using the
>>higher version.
>>      you will need To keep it at version 13.6.
>>          I can窶冲 think of another way to do it
>>          Good luck
>>          Soledad Attia
>>          
>>------------------------------------------------------------------------
>>     *From:* icu-pcb-forum-bounce@xxxxxxxxxxxxx
>>    
>><_javascript_:parent.ComposeTo("icu-pcb-forum-bounce%40freelists.org",
>>     "");> [mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx
>>    
>><_javascript_:parent.ComposeTo("icu-pcb-forum-bounce%40freelists.org",
>>     "");>] *On Behalf Of *arimitsu seiji
>>     *Sent:* Wednesday, February 07, 2007 8:51 AM
>>     *To:* icu-pcb-forum@xxxxxxxxxxxxx
>>     <_javascript_:parent.ComposeTo("icu-pcb-forum%40freelists.org",
>>"");>
>>     *Subject:* [PCB_FORUM] Is it possible to down rev from version
>>     15-->14-->13?
>>          Hi all,
>>          It seems like I can窶冲 stop running into trouble these
>>days :)          Lets say I have a customer using Version 13.6 and
>>we no longer
>>     have it installed.  I currently have access to Version 14 and
>>15.     Is it possible to use one of these versions and down rev
>>the data
>>     down back to 13.6 after we are done with routing.  We need to
>>keep
>>     it at 13.6 for customer purpose.  I thought about just
>>importing
>>     and exporting subdrawing but I remember it having some issues
>>in
>>     the past and it is a pretty dense board so I'm afraid I might
>>miss
>>     something.
>>          If anyone have any idea/suggestions please let me know.
>>          Thank you,
>>     Seiji
>>     ----------------------------------------------------------- To
>>     subscribe/unsubscribe: Send a message to
>>     icu-pcb-forum-request@xxxxxxxxxxxxx
>>    
>><_javascript_:parent.ComposeTo("icu-pcb-forum-request%40freelists.org",
>>     "");> with a subject of subscribe or unsubscribe To view the
>>     archives of this list go to
>>     http://www.freelists.org/archives/icu-pcb-forum/ Problems or
>>     Questions: Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx
>>    
>><_javascript_:parent.ComposeTo("icu-pcb-forum-admins%40freelists.org",
>>     "");>
>>-----------------------------------------------------------
>>
>>----------------------------------------------------------- To
>>subscribe/unsubscribe: Send a message to
>>icu-pcb-forum-request@xxxxxxxxxxxxx
>><_javascript_:parent.ComposeTo("icu-pcb-forum-request%40freelists.org",
>>"");> with a subject of subscribe or unsubscribe To view the
>>archives of this list go to
>>http://www.freelists.org/archives/icu-pcb-forum/ Problems or
>>Questions: Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx
>><_javascript_:parent.ComposeTo("icu-pcb-forum-admins%40freelists.org",
>>"");> -----------------------------------------------------------
>>------------------------------------------------------------------------
>>*Check Out the new free AIM(R) Mail*
>><http://pr.atwola.com/promoclk/100122638x1081283466x1074645346/aol?redir=http%3A%2F%2Fwww%2Eaim%2Ecom%2Ffun%2Fmail%2F>
>>-- 2 GB of storage and industry-leading spam and email virus
>>protection.
>
>
>-----------------------------------------------------------
>To subscribe/unsubscribe: Send a message to
>icu-pcb-forum-request@xxxxxxxxxxxxx
>with a subject of subscribe or unsubscribe
>
>To view the archives of this list go to
>http://www.freelists.org/archives/icu-pcb-forum/
>
>Problems or Questions:
>Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx
>-----------------------------------------------------------

All trademarks and copyrights within the FreeLists archives are owned by their respective owners. Everything else ©2000-2009 Avenir Technologies, LLC. FreeLists is a service of Avenir Technologies, LLC.