[PCB_FORUM] Re: Question regarding the netlength.il skill file

A funny thing happened on the way to... Unix (being back on Unix/Linix I
found out)

If you're running allegro on Uni/Linix, make sure you're aware of the file
names Case. If the netlength.il file is actually called NetLength.il make
SURE the case gets carried over to the .ilinit file. If it's not EXACTLY
the same allegro won't find it. Hense, it won't get installed.

Good day.
Mitch


> ----- Original Message ----
> From: arimitsu seiji <arimitsus@xxxxxxxxxxx>
> To: icu-pcb-forum@xxxxxxxxxxxxx
> Sent: Friday, February 9, 2007 4:22:53 PM
> Subject: [PCB_FORUM] Re: Question regarding the netlength.il skill file
>
> I am running it in a writable
> directory.
>
> I have looked for the line that was suggested on the message Mitch
> posted, but I had no luck finding the line.  I tried loading
> "drc_walk.il" to see if it would give me the same error but "drc_walk.il"
> works just fine.  Does anyone else have problems with the
> netlength.il?  And if you don't then is it worth trying to get it
> working?  Thank you all in advance.
>
>
>
>
>
> From: <george.h.patrick@xxxxxxxxxxxxxx>
> Reply-To:
> icu-pcb-forum@xxxxxxxxxxxxx
> To:
> <icu-pcb-forum@xxxxxxxxxxxxx>
> Subject: [PCB_FORUM] Re:
> Question regarding the netlength.il skill file
> Date: Fri, 9 Feb
> 2007 12:50:29 -0800
>
>
>
>
>
> Are you running it in a directory you can write
> to?
>
>
>
>
>
> --
> George Patrick
> Tektronix, Inc.
> Central Engineering, EDS Applications
> Support
>
> P.O. Box 500, M/S 39-512
> Beaverton,
> OR 97077-0001
> ã?? 503-627-5272
> (voice)     ã?? 503-627-5587 (fax)
> http://www.tektronix.com    http://www.pcb-designer.com
>
>
> "Off-Grid and Proud of
> it!"
>
>
>
>
> -----Original Message-----
> From:
> icu-pcb-forum-bounce@xxxxxxxxxxxxx
> [mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of arimitsu
> seiji
> Sent: Thursday, February 08, 2007 16:24
> To:
> icu-pcb-forum@xxxxxxxxxxxxx
> Subject: [PCB_FORUM] Re: Question
> regarding the netlength.il skill file
>
>
>
>
>
> I loaded it in the illinit file and it is being loaded, but still run
> into the same error.  I am running Allegro expert and not the studio
> version.  Does anyone have any more ideas?
>
>
>
>
>
>
>
>
>
>
> From:  gnieski_mike@xxxxxxx
> Reply-To:  icu-pcb-forum@xxxxxxxxxxxxx
> To:  <icu-pcb-forum@xxxxxxxxxxxxx>
> Subject:  [PCB_FORUM]
> Re: IDF IN problem
> Date:  Thu, 8 Feb 2007 08:22:29
> -0500
>>15.5.1
>>
>>
>>-----Original
> Message-----
>>From:
> icu-pcb-forum-bounce@xxxxxxxxxxxxx
>>[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx]
> On Behalf Of Shahed
>>Safavi-Bayat
>>Sent: Thursday, February 08,
> 2007 8:18 AM
>>To: icu-pcb-forum@xxxxxxxxxxxxx
>>Subject:
> [PCB_FORUM] Re: IDF IN problem
>>
>>What Version of Allegro you
> are using? Is it
> 15.7?
>>
>>
>>Shahed
>>
>>
>>-----Original
> Message-----
>>From:
> icu-pcb-forum-bounce@xxxxxxxxxxxxx
>>[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx]On
> Behalf Of
>>gnieski_mike@xxxxxxx
>>Sent: Thursday, February 08,
> 2007 6:41 AM
>>To: icu-pcb-forum@xxxxxxxxxxxxx
>>Subject:
> [PCB_FORUM] IDF IN problem
>>
>>
>> This is for anyone that
> uses Import-idf in Allegro. Presently we
>>import idf placement and
> board outline
>> data from SolidWorks. I'd like to see if anyone has
> seen a
>>problem reading in placement files and having
>>
> components NOT move if the mechanical data wants it to? We have
>>a
> board with two LED's placed using
>> the wrong orientation, the lens
> of the LED facing inboard. The
>>orientation and origin of the part
> both agree
>> in the mech model and in the Allegro footprint. After
> reading
>>the .emn file into the board to see if it corrects
>>
> the orientation of the LED it DOES NOT not move, still
> facing
>>inboard. If I manually move the part a few mils away
>>
> or delete the part and re-read the same identical .emn file into
>>the
> board it places the part in the proper
>> location and proper
> orientation facing outboard. I'm not quite
>>sure at what point the
> inboard orientation happened
>> and don't understand why reading in
> the same .emn file results
>>in two different orientations. After
> looking at
>> the .emn file we noticed that the orientation of the
> part is at
>>-90.....As Allegro always show deg in positive
>>
> increments is it possible that this could be a problem? Has
>>anyone
> else seen this happen?
>>
>> thanks,
>>
>> Mike
> Gnieski
>> EMC2 Corporation
>> Hopkinton,
> MA
>>
>>-----------------------------------------------------------
>>To
> subscribe/unsubscribe:
>>Send a message to
> icu-pcb-forum-request@xxxxxxxxxxxxx
>>with a subject of subscribe or
> unsubscribe
>>
>>To view the archives of this list go
> to
>>http://www.freelists.org/archives/icu-pcb-forum/
>>
>>Problems
> or Questions:
>>Send an email to
> icu-pcb-forum-admins@xxxxxxxxxxxxx
>>-----------------------------------------------------------
>>-----------------------------------------------------------
>>To
> subscribe/unsubscribe:
>>Send a message to
> icu-pcb-forum-request@xxxxxxxxxxxxx
>>with a subject of subscribe or
> unsubscribe
>>
>>To view the archives of this list go
> to
>>http://www.freelists.org/archives/icu-pcb-forum/
>>
>>Problems
> or Questions:
>>Send an email to
> icu-pcb-forum-admins@xxxxxxxxxxxxx
>>-----------------------------------------------------------
>>
>>-----------------------------------------------------------
>>To
> subscribe/unsubscribe:
>>Send a message to
> icu-pcb-forum-request@xxxxxxxxxxxxx
>>with a subject of subscribe or
> unsubscribe
>>
>>To view the archives of this list go to
> http://www.freelists.org/archives/icu-pcb-forum/
>>
>>Problems or
> Questions:
>>Send an email to
> icu-pcb-forum-admins@xxxxxxxxxxxxx
>>-----------------------------------------------------------
>
> -----------------------------------------------------------
> To subscribe/unsubscribe: Send a message to
> icu-pcb-forum-request@xxxxxxxxxxxxx with a subject of subscribe or
> unsubscribe To view the archives of this list go to
> http://www.freelists.org/archives/icu-pcb-forum/ Problems or Questions:
> Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx
> -----------------------------------------------------------
>
>
> -----------------------------------------------------------
> To subscribe/unsubscribe:
> Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx
> with a subject of subscribe or unsubscribe
>
> To view the archives of this list go to
> http://www.freelists.org/archives/icu-pcb-forum/
>
> Problems or Questions:
> Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx
> -----------------------------------------------------------
>
>
>
>
>
>
>
> ____________________________________________________________________________________
> 8:00? 8:25? 8:40? Find a flick in no time
> with the Yahoo! Search movie showtime shortcut.
> http://tools.search.yahoo.com/shortcuts/#news



-----------------------------------------
Stay ahead of the information curve.
Receive PCB news and jobs on your desktop daily.
Subscribe today to the PCB CafeNews newsletter.
[ http://www10.pcbcafe.com/nl/newsletter_subscribe.php ]
It's informative and essential.
This message was sent to you from a machine at 192.35.156.11
-----------------------------------------------------------
To subscribe/unsubscribe: 
Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx
with a subject of subscribe or unsubscribe

To view the archives of this list go to 
http://www.freelists.org/archives/icu-pcb-forum/

Problems or Questions:
Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx
-----------------------------------------------------------

Other related posts: