[PCB_FORUM] Re: Question regarding the netlength.il skill file

Hey Seiji,

Does your allegro.ilinit file has setSkillPath() command used? Where your skill 
files are placed.. directly inside the pcbenv folder or into a subfolder??
cut and paste the content inside the allegro.ilinit file.I can give a try 
looking into that.

Thanks,
Raj.



----- Original Message ----
From: arimitsu seiji <arimitsus@xxxxxxxxxxx>
To: icu-pcb-forum@xxxxxxxxxxxxx
Sent: Friday, February 9, 2007 4:22:53 PM
Subject: [PCB_FORUM] Re: Question regarding the netlength.il skill file

I am running it in a writable 
directory.

I have looked for the line that was suggested on the message Mitch 
posted, but I had no luck finding the line.  I tried loading 
"drc_walk.il" to see if it would give me the same error but "drc_walk.il" 
works just fine.  Does anyone else have problems with the 
netlength.il?  And if you don't then is it worth trying to get it 
working?  Thank you all in advance.





From: <george.h.patrick@xxxxxxxxxxxxxx>
Reply-To: 
icu-pcb-forum@xxxxxxxxxxxxx
To: 
<icu-pcb-forum@xxxxxxxxxxxxx>
Subject: [PCB_FORUM] Re: 
Question regarding the netlength.il skill file
Date: Fri, 9 Feb 
2007 12:50:29 -0800


 
 

Are you running it in a directory you can write 
to?

 



-- 
George Patrick
Tektronix, Inc.
Central Engineering, EDS Applications 
Support

P.O. Box 500, M/S 39-512
Beaverton, 
OR 97077-0001
ナ 503-627-5272 
(voice)     ニ 503-627-5587 (fax)
http://www.tektronix.com    http://www.pcb-designer.com

 
"Off-Grid and Proud of 
it!"




-----Original Message-----
From: 
icu-pcb-forum-bounce@xxxxxxxxxxxxx 
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of arimitsu 
seiji
Sent: Thursday, February 08, 2007 16:24
To: 
icu-pcb-forum@xxxxxxxxxxxxx
Subject: [PCB_FORUM] Re: Question 
regarding the netlength.il skill file





I loaded it in the illinit file and it is being loaded, but still run 
into the same error.  I am running Allegro expert and not the studio 
version.  Does anyone have any more ideas?










From:  gnieski_mike@xxxxxxx
Reply-To:  icu-pcb-forum@xxxxxxxxxxxxx
To:  <icu-pcb-forum@xxxxxxxxxxxxx>
Subject:  [PCB_FORUM] 
Re: IDF IN problem
Date:  Thu, 8 Feb 2007 08:22:29 
-0500
>15.5.1
>
>
>-----Original 
Message-----
>From: 
icu-pcb-forum-bounce@xxxxxxxxxxxxx
>[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] 
On Behalf Of Shahed
>Safavi-Bayat
>Sent: Thursday, February 08, 
2007 8:18 AM
>To: icu-pcb-forum@xxxxxxxxxxxxx
>Subject: 
[PCB_FORUM] Re: IDF IN problem
>
>What Version of Allegro you 
are using? Is it 
15.7?
>
>
>Shahed
>
>
>-----Original 
Message-----
>From: 
icu-pcb-forum-bounce@xxxxxxxxxxxxx
>[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx]On 
Behalf Of
>gnieski_mike@xxxxxxx
>Sent: Thursday, February 08, 
2007 6:41 AM
>To: icu-pcb-forum@xxxxxxxxxxxxx
>Subject: 
[PCB_FORUM] IDF IN problem
>
>
> This is for anyone that 
uses Import-idf in Allegro. Presently we
>import idf placement and 
board outline
> data from SolidWorks. I'd like to see if anyone has 
seen a
>problem reading in placement files and having
> 
components NOT move if the mechanical data wants it to? We have
>a 
board with two LED's placed using
> the wrong orientation, the lens 
of the LED facing inboard. The
>orientation and origin of the part 
both agree
> in the mech model and in the Allegro footprint. After 
reading
>the .emn file into the board to see if it corrects
> 
the orientation of the LED it DOES NOT not move, still 
facing
>inboard. If I manually move the part a few mils away
> 
or delete the part and re-read the same identical .emn file into
>the 
board it places the part in the proper
> location and proper 
orientation facing outboard. I'm not quite
>sure at what point the 
inboard orientation happened
> and don't understand why reading in 
the same .emn file results
>in two different orientations. After 
looking at
> the .emn file we noticed that the orientation of the 
part is at
>-90.....As Allegro always show deg in positive
> 
increments is it possible that this could be a problem? Has
>anyone 
else seen this happen?
>
> thanks,
>
> Mike 
Gnieski
> EMC2 Corporation
> Hopkinton, 
MA
>
>-----------------------------------------------------------
>To 
subscribe/unsubscribe:
>Send a message to 
icu-pcb-forum-request@xxxxxxxxxxxxx
>with a subject of subscribe or 
unsubscribe
>
>To view the archives of this list go 
to
>http://www.freelists.org/archives/icu-pcb-forum/
>
>Problems 
or Questions:
>Send an email to 
icu-pcb-forum-admins@xxxxxxxxxxxxx
>-----------------------------------------------------------
>-----------------------------------------------------------
>To 
subscribe/unsubscribe:
>Send a message to 
icu-pcb-forum-request@xxxxxxxxxxxxx
>with a subject of subscribe or 
unsubscribe
>
>To view the archives of this list go 
to
>http://www.freelists.org/archives/icu-pcb-forum/
>
>Problems 
or Questions:
>Send an email to 
icu-pcb-forum-admins@xxxxxxxxxxxxx
>-----------------------------------------------------------
>
>-----------------------------------------------------------
>To 
subscribe/unsubscribe:
>Send a message to 
icu-pcb-forum-request@xxxxxxxxxxxxx
>with a subject of subscribe or 
unsubscribe
>
>To view the archives of this list go to 
http://www.freelists.org/archives/icu-pcb-forum/
>
>Problems or 
Questions:
>Send an email to 
icu-pcb-forum-admins@xxxxxxxxxxxxx
>-----------------------------------------------------------

----------------------------------------------------------- 
To subscribe/unsubscribe: Send a message to 
icu-pcb-forum-request@xxxxxxxxxxxxx with a subject of subscribe or 
unsubscribe To view the archives of this list go to 
http://www.freelists.org/archives/icu-pcb-forum/ Problems or Questions: 
Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx 
----------------------------------------------------------- 


-----------------------------------------------------------
To subscribe/unsubscribe: 
Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx
with a subject of subscribe or unsubscribe

To view the archives of this list go to 
http://www.freelists.org/archives/icu-pcb-forum/

Problems or Questions:
Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx
-----------------------------------------------------------






 
____________________________________________________________________________________
8:00? 8:25? 8:40? Find a flick in no time 
with the Yahoo! Search movie showtime shortcut.
http://tools.search.yahoo.com/shortcuts/#news

Other related posts: