[PCB_FORUM] Re: Move component with unwanted traces

 

Don't know if Netscape has caught up with their Open Source cousin
Thunderbird yet, but you can click on the Edit Filters menu (I am not at
home, so I can't give all the clicks) item and filter much more
extensively than in Outlook inside TBird.

 

I haven't used Eudora in years, but when I want to their home page
(www.eudora.com <http://www.eudora.com/> ) and searched the knowledge
base using "filter" there were 32 messages in the resulting thread.  I
would be VERY surprised if you couldn't do content filtering in
Eudora...

 

-- 
George Patrick
Tektronix, Inc.
Central Engineering, EDS Applications Support
P.O. Box 500, M/S 39-512
Beaverton, OR 97077-0001
* 503-627-5272 (voice)     * 503-627-5587 (fax)
<http://www.tektronix.com/> 
http://www.tektronix.com     <http://www.pcb-designer.com>
http://www.pcb-designer.com
 
"Off-Grid and Proud of it!"

-----Original Message-----
From: icu-pcb-forum-bounce@xxxxxxxxxxxxx
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of Mark Salberg
Sent: Wednesday, August 16, 2006 08:06
To: icu-pcb-forum@xxxxxxxxxxxxx
Subject: [PCB_FORUM] Re: Move component with unwanted traces

 

Thanks Gary.
 We use Netscape and Eudora, but can not find how to filter it out.
Anyone have it set in Netscape?

Mark

Gary MacIndoe wrote:



Mark,
 
In Outlook, Tools -> Rules and Alerts..., E-mail Rules tab.
 
I have it set to weed out several combinations of "Out of Office" (upper
case, lower case etc.) from the subject line.
 
Gary E. MacIndoe
PCB Design Engineer
Advanced Micro Devices
Longmont, Colorado 
 
-----Original Message-----
From: icu-pcb-forum-bounce@xxxxxxxxxxxxx
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of Mark Salberg
Sent: Wednesday, August 16, 2006 5:31 AM
To: icu-pcb-forum@xxxxxxxxxxxxx
Subject: [PCB_FORUM] Re: Move component with unwanted traces
 
Is there a way to block the auto replies that 14 people are "out of the 
office"?
I get them whenever I post a question.
Well...here we go again.
 
Thanks,
Mark
 
Mark Salberg wrote:
 
  

Hello all,
When we move a component...with or without "stretch" selected. Some 
traces and vias move with it.
We have run DBFIX but still repeats. Now we need to delete the trace, 
move the part, then re-route.  :-(
 
Only happens on some components...not all.
 
Any suggestions?
Thanks,
Mark
 
 
 
    

________________________________________________________________________
____
_ 
  

Scanned by IBM Email Security Management Services powered by 
MessageLabs. For more information please visit http://www.ers.ibm.com
 
    

________________________________________________________________________
____
_ 
  

-----------------------------------------------------------
To subscribe/unsubscribe: Send a message to 
icu-pcb-forum-request@xxxxxxxxxxxxx
with a subject of subscribe or unsubscribe
 
To view the archives of this list go to 
http://www.freelists.org/archives/icu-pcb-forum/
 
Problems or Questions:
Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx
-----------------------------------------------------------
 
 
    

________________________________________________________________________
____
_ 
  

Scanned by IBM Email Security Management Services powered by 
MessageLabs. For more information please visit http://www.ers.ibm.com
 
    

________________________________________________________________________
____
_ 
  

 
    

 
 
________________________________________________________________________
____
_
Scanned by IBM Email Security Management Services powered by
MessageLabs.
For more information please visit http://www.ers.ibm.com
________________________________________________________________________
____
_
-----------------------------------------------------------
To subscribe/unsubscribe: 
Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx
with a subject of subscribe or unsubscribe
 
To view the archives of this list go to
http://www.freelists.org/archives/icu-pcb-forum/
 
Problems or Questions:
Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx
-----------------------------------------------------------
 
 
 
 
 
-----------------------------------------------------------
To subscribe/unsubscribe: 
Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx
with a subject of subscribe or unsubscribe
 
To view the archives of this list go to
http://www.freelists.org/archives/icu-pcb-forum/
 
Problems or Questions:
Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx
-----------------------------------------------------------
 
________________________________________________________________________
_____
Scanned by IBM Email Security Management Services powered by
MessageLabs. For more information please visit http://www.ers.ibm.com
________________________________________________________________________
_____
 
  


________________________________________________________________________
_____
Scanned by IBM Email Security Management Services powered by
MessageLabs. For more information please visit http://www.ers.ibm.com
________________________________________________________________________
_____

Other related posts: