[PCB_FORUM] Re: EMN and EMP files

Gene,

        Not that I know of. I read it into ProE myself and create
the assembly for the mechanical engineer.

Jerry

-----Original Message-----
From: Gene Carman [mailto:gcarman@xxxxxxxxxxxxxxx] 
Sent: Monday, January 31, 2005 12:47 PM
To: icu-pcb-forum@xxxxxxxxxxxxx
Subject: [PCB_FORUM] Re: EMN and EMP files


is there any reader available to look at this stuff myself?  Is there any check
I can perform on the data before sending it out to the ME, to ensure that the
data I hand off is good?

Thanks for the info.

-----Original Message-----
From: Schwartz, Jerome [mailto:jschwa01@xxxxxxxxxx]
Sent: Monday, January 31, 2005 9:43 AM
To: 'icu-pcb-forum@xxxxxxxxxxxxx'
Subject: [PCB_FORUM] Re: EMN and EMP files


Yes,

        A few possibilities.

1. You have multiple board outlines.
2. You have a non-continuous board outline
3. You have parts with large power groups.
4. You have too many vias.
5. You have place boundaries with over lapping vertices, and or part or route
keep-in/keep-outs
   with the same.
6. The thickness of the design is less than the diameter of the smallest hole
feature. 

That's all I can think of right now.

 Regards,
      Jerry Schwartz, CID+
      IPC Advanced Certified Designer
     "May The Schwartz Be With You."

Designer 3
Harris Corporation GCSD              Voice (321)-727-5474
P.O. Box 37, MS 1/3232               Pager (321)-690-9797
Melbourne, FL 32902-0037           
mailto:Jerome.Schwartz@xxxxxxxxxx           
http://www.harris.com





-----Original Message-----
From: MAILER-DAEMON@xxxxxxxxxxxxx [mailto:MAILER-DAEMON@xxxxxxxxxxxxx] 
Sent: Monday, January 31, 2005 12:34 PM
To: icu-pcb-forum@xxxxxxxxxxxxx
Subject: [PCB_FORUM] EMN and EMP files


Recently I prepared the usual EMN and EMP files for a mechanical engineer...  I
did not use any unusual settings, and looking at the files the data seems to all
be there, but the ME is now saying he cannot read the EMN file.  Anybody have
any suggestions?  Has anybody run into anything similar?

Output was PTC ver 2.0.

using 15.2 s032 on Win 2K.  
-----------------------------------------------------------
To subscribe/unsubscribe: 
        Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx
        with a subject of subscribe or unsubscribe

To view the archives of this list please login at
http://www.freelists.org. Our list name is icu-pcb-forum
or go to http://www.freelists.org/archives/icu-pcb-forum/

Problems or Questions:
        Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx

Want to post a job listing ?  DON'T DO IT HERE!  
Better yet, join our jobs listing forum.

SUBSCRIBE:  icu-jobs-forum-subscribe@xxxxxxxxxx
POST:       icu-jobs-forum@xxxxxxxxxx
-----------------------------------------------------------
-----------------------------------------------------------
To subscribe/unsubscribe: 
        Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx
        with a subject of subscribe or unsubscribe

To view the archives of this list please login at
http://www.freelists.org. Our list name is icu-pcb-forum
or go to http://www.freelists.org/archives/icu-pcb-forum/

Problems or Questions:
        Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx

Want to post a job listing ?  DON'T DO IT HERE!  
Better yet, join our jobs listing forum.

SUBSCRIBE:  icu-jobs-forum-subscribe@xxxxxxxxxx
POST:       icu-jobs-forum@xxxxxxxxxx
-----------------------------------------------------------
-----------------------------------------------------------
To subscribe/unsubscribe: 
        Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx
        with a subject of subscribe or unsubscribe

To view the archives of this list please login at
http://www.freelists.org. Our list name is icu-pcb-forum
or go to http://www.freelists.org/archives/icu-pcb-forum/

Problems or Questions:
        Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx

Want to post a job listing ?  DON'T DO IT HERE!  
Better yet, join our jobs listing forum.

SUBSCRIBE:  icu-jobs-forum-subscribe@xxxxxxxxxx
POST:       icu-jobs-forum@xxxxxxxxxx
-----------------------------------------------------------
-----------------------------------------------------------
To subscribe/unsubscribe: 
        Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx
        with a subject of subscribe or unsubscribe

To view the archives of this list please login at
http://www.freelists.org. Our list name is icu-pcb-forum
or go to http://www.freelists.org/archives/icu-pcb-forum/

Problems or Questions:
        Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx

Want to post a job listing ?  DON'T DO IT HERE!  
Better yet, join our jobs listing forum.

SUBSCRIBE:  icu-jobs-forum-subscribe@xxxxxxxxxx
POST:       icu-jobs-forum@xxxxxxxxxx
-----------------------------------------------------------

Other related posts: