[PCB_FORUM] Re: Drill Legend probs

Dennis and all who replied,

 

Thanks to all, I finally found it!  This drill legend is so long, that I
finally saw two entries for 2.4 non-plated holes.

These two different padstacks had the same 2.4 drill, same Circle/y for
Figure/Character, but different Width and Height numbers.

 

Now that error went away, but the Drill Legend table has pretty much
zero width (it looks like a vertical line when zoomed out)!

I am pointing to the "default-mm.dlt" drill template file, so I can't
imagine what that could be.

The design I am currently working on creates the table just fine.

 

Thanks for the suggestions!

Gary

 

 

  

Gary E. MacIndoe
PCB Design Engineer
Longmont, Colorado

amd.com

gary.macindoe@xxxxxxx

________________________________

From: icu-pcb-forum-bounce@xxxxxxxxxxxxx
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of Dennis Compeau
Sent: Monday, April 09, 2007 3:41 PM
To: icu-pcb-forum@xxxxxxxxxxxxx
Subject: [PCB_FORUM] Re: Drill Legend probs

 


Hi Gary, 

Did you try to delete the symbol or via and run it - does the error
messasge go away? 

Maybe a corrupt symbol - 

Did you do a DB doctor? 

Dennis 





"Macindoe, Gary" <Gary.Macindoe@xxxxxxx> 
Sent by: icu-pcb-forum-bounce@xxxxxxxxxxxxx 

04/09/2007 03:17 PM 

Please respond to
icu-pcb-forum@xxxxxxxxxxxxx

To

icu-pcb-forum@xxxxxxxxxxxxx 

cc

 

Subject

[PCB_FORUM] Re: Drill Legend probs

 

 

 




Jean, 
  
Thanks for the reply. Yes, it looks like the consensus is that 2.4 is
the drill size.  I ran NC Drill and 2.4 is a drill size used in *one*
place only! 
From the cryptic error message it would appear that there are more than
one 2.4 drill padstacks, each with a different Figure, but there's only
one. 
  
Thanks for the help, 
  
Gary 
  

  
Gary E. MacIndoe 
PCB Design Engineer 
Longmont, Colorado 
  
amd.com 
gary.macindoe@xxxxxxx <mailto:gary.macindoe@xxxxxxx>  
  

 

________________________________


From: icu-pcb-forum-bounce@xxxxxxxxxxxxx
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of Jean Bratton
Sent: Monday, April 09, 2007 2:47 PM
To: icu-pcb-forum@xxxxxxxxxxxxx
Subject: [PCB_FORUM] Re: Drill Legend probs 
  
I'm thinking 2.4 is the drill size, and that you have some 2.4 drills
with one figure and some with another...??? 
  

 

________________________________


From: icu-pcb-forum-bounce@xxxxxxxxxxxxx
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of Macindoe, Gary
Sent: Monday, April 09, 2007 4:32 PM
To: icu-pcb-forum@xxxxxxxxxxxxx
Subject: [PCB_FORUM] Drill Legend probs 
  
Hey guys, 
  
I'm trying to help a fellow designer in our company (remotely). I have a
copy of his database, it's setup as Metric. 
  
15.5.1, XP Pro. 
  
When running Manufacture -> NC -> Drill Legend, it fails with the
following message: 
  
>>> Begin processing drill holes. 
>>> Warning : Hole 2.4000-0.0000-C-N-0.0000-0.0000 uses multiple drill
figures. 
>>> End processing drill holes. 
  
To me it looked like "2.4000-0.0000" were coordinates, but there is no
hole there. 
I've not seen this one, but I have had two different padstacks with the
same drill figure, which runs fine. 
  
Any ideas as to how to find the offending hole? 
  
Thanks, 
  
Gary 
  
  
  
  
Gary E. MacIndoe 
PCB Design Engineer 
Longmont, Colorado 
  
amd.com 
gary.macindoe@xxxxxxx 
  
  
  
  

This correspondence and any attachments are considered confidential. If
you are not the intended recipient, please notify Freedom CAD Services,
Inc. immediately by either replying to this message or by sending an
email to operations@xxxxxxxxxxxxxx; please destroy all copies of this
message and any attachments. Thank you.

GIF image

Other related posts: