[PCB_FORUM] Re: Dangling lines and stubs, automatic delete using skill.

Peter,
 
Copy database was just a statement not a command.
 
If you "Only" have Line Smoothing on and "Only have "dangling lines" checked.
 
Tt will nor mess up your diff pairs. (unless of course you have dangling lines 
on your diff pairs. But adding no gloss or fixing the diff pairs will resolve 
that.  I do this all the time and it works great.
 
 
regards,
Gerry

 Gerry Meier
Sr. PCB Designer
Freedom CAD Services, Inc.
Voice: (603) 864-1300 x1350
Alt. Voice: (386) 753-0048
Email: gerry.meier@xxxxxxxxxxxxxx
visit our website at<http://www.freedomcad.com <http://www.freedomcad.com/> 



 

________________________________

From: Peter Sørensen [mailto:sorensen@xxxxxxxxxxx] 
Sent: Tuesday, December 21, 2004 10:43 AM
To: icu-pcb-forum@xxxxxxxxxxxxx
Subject: [PCB_FORUM] Re: Dangling lines and stubs, automatic delete using skill.


(Sorry about the double send)
Hi Gerry
 
I use allegro 15.1. I can't use gloss line smoothing because of a fault. Gloss 
line smoothing  ruines diff traces evenif you have the nogloss option set on 
all diff lines.
 
Copy database? I don't know this command. Where do I find it?
 
 
Hi 
Peter Sørensen 
MTS Engineer 
Ethernet Product Group 
Vitesse Semiconductor Corporation 
Location: Denmark 
Tlf    +45 4485-5996 
Cell  +45 4050-7098 
Fax. +45 4485-5939 



 
 

        -----Original Message-----
        From: Gerry Meier [mailto:gerry.meier@xxxxxxxxxxxxxx]
        Sent: 21. december 2004 14:29
        To: icu-pcb-forum@xxxxxxxxxxxxx
        Subject: [PCB_FORUM] Re: Dangling lines and stubs, automatic delete 
using skill.
        
        
        Peter,
         
        You can try using the Gloss command - This  works well for me it may 
leave those not attached to  a net.
         
         "in a copy database" try glossing the dangling lines have "only" line 
smoothing checked and "only" dangling lines inside line smoothing form checked.
         

         Gerry Meier
        Sr. PCB Designer
        Freedom CAD Services, Inc.
        Voice: (603) 864-1300 x1350
        Alt. Voice: (386) 753-0048
        Email: gerry.meier@xxxxxxxxxxxxxx
        visit our website at<http://www.freedomcad.com 
<http://www.freedomcad.com/> 
        
        

         

________________________________

        From: Peter Sørensen [mailto:sorensen@xxxxxxxxxxx] 
        Sent: Tuesday, December 21, 2004 8:13 AM
        To: icu-pcb-forum@xxxxxxxxxxxxx
        Subject: [PCB_FORUM] Dangling lines and stubs, automatic delete using 
skill.
        
        
        Hi
         
        I would like a skill program that can delete all dangling lines.
        I tryed to run these skill scripts but get error messages like can't 
find Dangling and can't Find stubs.
        My guess is tha some form files are missing. I tryed the skill archive 
on sourcelink too but also here a form files seems to be missing.
        If thes files can find the dangling lines for me I guess I will be able 
to add some skill code that will delete them as well.
         
        Hi 
        Peter Sørensen 
        MTS Engineer 
        Ethernet Product Group 
        Vitesse Semiconductor Corporation 
        Location: Denmark 
        Tlf    +45 4485-5996 
        Cell  +45 4050-7098 
        Fax. +45 4485-5939 



                -----Original Message-----
                From: Van Huynh (huynh) [mailto:huynh@xxxxxxxxx]
                Sent: 18. december 2004 19:39
                To: icu-pcb-forum@xxxxxxxxxxxxx
                Subject: [PCB_FORUM] Re: Help!!! Segment with same start and 
end points
                
                
                My dangling report is clean.
                It's seem like I have some elements out of dwg extend and I can 
not get to it.
                 
                Van Huynh
                
                 

________________________________

                From: Selvakumar [mailto:selva@xxxxxxxxxxxxx] 
                Sent: Saturday, December 18, 2004 10:29 AM
                To: icu-pcb-forum@xxxxxxxxxxxxx
                Subject: [PCB_FORUM] Re: Help!!! Segment with same start and 
end points
                
                
                Please run these allego scripts.This will show the 
danglings.validate the dangling and delete.
                 
                regards
                Selva

                        -----Original Message-----
                        From: Gerry Meier [mailto:gerry.meier@xxxxxxxxxxxxxx]
                        Sent: Saturday, December 18, 2004 11:23 PM
                        To: icu-pcb-forum@xxxxxxxxxxxxx
                        Subject: [PCB_FORUM] Re: Help!!! Segment with same 
start and end points
                        
                        
                        Van,
                         
                        When you run your summary report  or dangling line 
report are there dangling lines?
                        If so  "in a copy database" try glossing the dangling 
lines have "only" line smoothing checked and "only" dangling lines inside line 
smoothing form checked.
                         
                        Gerry
                         

                         Gerry Meier
                        Sr. PCB Designer
                        Freedom CAD Services, Inc.
                        Voice: (603) 864-1300 x1350
                        Alt. Voice: (386) 753-0048
                        Email: gerry.meier@xxxxxxxxxxxxxx
                        visit our website at<http://www.freedomcad.com 
<http://www.freedomcad.com/> 
                        
                        

                         

________________________________

                        From: Van Huynh (huynh) [mailto:huynh@xxxxxxxxx] 
                        Sent: Saturday, December 18, 2004 12:46 PM
                        To: icu-pcb-forum@xxxxxxxxxxxxx
                        Subject: [PCB_FORUM] Re: Help!!! Segment with same 
start and end points 
                        
                        
                        I ran DBDoctor within the database and outside on the 
shell command line still doesn't help.
                        Thanks for input
                         
                        Van Huynh
                        
                         
                         

________________________________

                        From: Gerry Meier [mailto:gerry.meier@xxxxxxxxxxxxxx] 
                        Sent: Saturday, December 18, 2004 9:41 AM
                        To: icu-pcb-forum@xxxxxxxxxxxxx
                        Subject: [PCB_FORUM] Re: Help!!! Segment with same 
start and end points 
                        
                        
                        try running dbdoctor on the database
                         

                         Gerry Meier
                        Sr. PCB Designer
                        Freedom CAD Services, Inc.
                        Voice: (603) 864-1300 x1350
                        Alt. Voice: (386) 753-0048
                        Email: gerry.meier@xxxxxxxxxxxxxx
                        visit our website at<http://www.freedomcad.com 
<http://www.freedomcad.com/> 
                        
                        

                         

________________________________

                        From: Van Huynh (huynh) [mailto:huynh@xxxxxxxxx] 
                        Sent: Saturday, December 18, 2004 12:37 PM
                        To: icu-pcb-forum@xxxxxxxxxxxxx
                        Subject: [PCB_FORUM] Help!!! Segment with same start 
and end points 
                        
                        
                        I got a lots of these warning on every artwork layers,
                        Any one know how to fix these errors message?
                         
                         WARNING: Segment with same start and end points at
                         (75.2869 -194448.6314) will be ignored.  Increasing 
output
                         accuracy may allow segment to be generated.
                         
                         
                        My artwork parameter setup:
                         
                        DEVICE-TYPE           GERBER_RS274X
                        OUTPUT-UNITS          INCHES
                        FILM-SIZE             240000 160000
                        FORMAT                2.5
                        ABORT-ON-ERROR        NO
                        SCALE                 1
                        SUPPRESS-LEAD-ZEROES  YES
                        SUPPRESS-TRAIL-ZEROES NO
                        SUPPRESS-EQUAL        YES
                        UNDEF-APT-CONT        NO
                         
                        NC Drill format is 2.5
                        Drawing parameter accuracy is 4
                         
                        Thank you
                        Van Huynh

Attachment: glossing.jpg
Description: glossing.jpg

Other related posts: