[PCB_FORUM] Re: Dangling lines and stubs, automatic delete using skill.

Peter,

This "find stubs" skill routine works stand alone, you do not need a form
file.  I am on 15.2, I just tried it and it works (even though it was
written for 13.x).  Put it where you have any other skill routines, load it
in with the "allegro.ilinit" file, then "find_stubs" to run it inside
Allegro.  Let me know if you need with it.

Gary E. MacIndoe
PCB Design Engineer
Advanced Micro Devices, Inc.
Longmont, Colorado


  -----Original Message-----
  From: Peter Sørensen [mailto:sorensen@xxxxxxxxxxx]
  Sent: Tuesday, December 21, 2004 6:13 AM
  To: icu-pcb-forum@xxxxxxxxxxxxx
  Subject: [PCB_FORUM] Dangling lines and stubs, automatic delete using
skill.


  Hi

  I would like a skill program that can delete all dangling lines.
  I tryed to run these skill scripts but get error messages like can't find
Dangling and can't Find stubs.
  My guess is tha some form files are missing. I tryed the skill archive on
sourcelink too but also here a form files seems to be missing.
  If thes files can find the dangling lines for me I guess I will be able to
add some skill code that will delete them as well.

  Hi
  Peter Sørensen
  MTS Engineer
  Ethernet Product Group
  Vitesse Semiconductor Corporation
  Location: Denmark
  Tlf    +45 4485-5996
  Cell  +45 4050-7098
  Fax. +45 4485-5939




    -----Original Message-----
    From: Van Huynh (huynh) [mailto:huynh@xxxxxxxxx]
    Sent: 18. december 2004 19:39
    To: icu-pcb-forum@xxxxxxxxxxxxx
    Subject: [PCB_FORUM] Re: Help!!! Segment with same start and end points


    My dangling report is clean.
    It's seem like I have some elements out of dwg extend and I can not get
to it.

    Van Huynh





----------------------------------------------------------------------------
    From: Selvakumar [mailto:selva@xxxxxxxxxxxxx]
    Sent: Saturday, December 18, 2004 10:29 AM
    To: icu-pcb-forum@xxxxxxxxxxxxx
    Subject: [PCB_FORUM] Re: Help!!! Segment with same start and end points


    Please run these allego scripts.This will show the danglings.validate
the dangling and delete.

    regards
    Selva
      -----Original Message-----
      From: Gerry Meier [mailto:gerry.meier@xxxxxxxxxxxxxx]
      Sent: Saturday, December 18, 2004 11:23 PM
      To: icu-pcb-forum@xxxxxxxxxxxxx
      Subject: [PCB_FORUM] Re: Help!!! Segment with same start and end
points


      Van,

      When you run your summary report  or dangling line report are there
dangling lines?
      If so  "in a copy database" try glossing the dangling lines have
"only" line smoothing checked and "only" dangling lines inside line
smoothing form checked.

      Gerry

       Gerry Meier
      Sr. PCB Designer
      Freedom CAD Services, Inc.
      Voice: (603) 864-1300 x1350
      Alt. Voice: (386) 753-0048
      Email: gerry.meier@xxxxxxxxxxxxxx
      visit our website at<http://www.freedomcad.com







--------------------------------------------------------------------------
      From: Van Huynh (huynh) [mailto:huynh@xxxxxxxxx]
      Sent: Saturday, December 18, 2004 12:46 PM
      To: icu-pcb-forum@xxxxxxxxxxxxx
      Subject: [PCB_FORUM] Re: Help!!! Segment with same start and end
points


      I ran DBDoctor within the database and outside on the shell command
line still doesn't help.
      Thanks for input

      Van Huynh






--------------------------------------------------------------------------
      From: Gerry Meier [mailto:gerry.meier@xxxxxxxxxxxxxx]
      Sent: Saturday, December 18, 2004 9:41 AM
      To: icu-pcb-forum@xxxxxxxxxxxxx
      Subject: [PCB_FORUM] Re: Help!!! Segment with same start and end
points


      try running dbdoctor on the database

       Gerry Meier
      Sr. PCB Designer
      Freedom CAD Services, Inc.
      Voice: (603) 864-1300 x1350
      Alt. Voice: (386) 753-0048
      Email: gerry.meier@xxxxxxxxxxxxxx
      visit our website at<http://www.freedomcad.com







--------------------------------------------------------------------------
      From: Van Huynh (huynh) [mailto:huynh@xxxxxxxxx]
      Sent: Saturday, December 18, 2004 12:37 PM
      To: icu-pcb-forum@xxxxxxxxxxxxx
      Subject: [PCB_FORUM] Help!!! Segment with same start and end points


      I got a lots of these warning on every artwork layers,
      Any one know how to fix these errors message?

       WARNING: Segment with same start and end points at
       (75.2869 -194448.6314) will be ignored.  Increasing output
       accuracy may allow segment to be generated.


      My artwork parameter setup:

      DEVICE-TYPE           GERBER_RS274X
      OUTPUT-UNITS          INCHES
      FILM-SIZE             240000 160000
      FORMAT                2.5
      ABORT-ON-ERROR        NO
      SCALE                 1
      SUPPRESS-LEAD-ZEROES  YES
      SUPPRESS-TRAIL-ZEROES NO
      SUPPRESS-EQUAL        YES
      UNDEF-APT-CONT        NO

      NC Drill format is 2.5
      Drawing parameter accuracy is 4

      Thank you
      Van Huynh

Other related posts: