[PCB_FORUM] Dangling lines and stubs, automatic delete using skill.

 
-----Original Message-----
From: Peter Sørensen 
Sent: 21. december 2004 14:13
To: 'icu-pcb-forum@xxxxxxxxxxxxx'
Subject: [PCB_FORUM] Dangling lines and stubs, automatic delete using skill.


Hi
 
I would like a skill program that can delete all dangling lines.
I tryed to run these skill scripts but get error messages like can't find 
Dangling and can't Find stubs.
My guess is tha some form files are missing. I tryed the skill archive on 
sourcelink too but also here a form files seems to be missing.
If thes files can find the dangling lines for me I guess I will be able to add 
some skill code that will delete them as well.
 
Hi 
Peter Sørensen 
MTS Engineer 
Ethernet Product Group 
Vitesse Semiconductor Corporation 
Location: Denmark 
Tlf    +45 4485-5996 
Cell  +45 4050-7098 
Fax. +45 4485-5939 



-----Original Message-----
From: Van Huynh (huynh) [mailto:huynh@xxxxxxxxx]
Sent: 18. december 2004 19:39
To: icu-pcb-forum@xxxxxxxxxxxxx
Subject: [PCB_FORUM] Re: Help!!! Segment with same start and end points


My dangling report is clean.
It's seem like I have some elements out of dwg extend and I can not get to it.
 
Van Huynh

 

  _____  

From: Selvakumar [mailto:selva@xxxxxxxxxxxxx] 
Sent: Saturday, December 18, 2004 10:29 AM
To: icu-pcb-forum@xxxxxxxxxxxxx
Subject: [PCB_FORUM] Re: Help!!! Segment with same start and end points


Please run these allego scripts.This will show the danglings.validate the 
dangling and delete.
 
regards
Selva

-----Original Message-----
From: Gerry Meier [mailto:gerry.meier@xxxxxxxxxxxxxx]
Sent: Saturday, December 18, 2004 11:23 PM
To: icu-pcb-forum@xxxxxxxxxxxxx
Subject: [PCB_FORUM] Re: Help!!! Segment with same start and end points


Van,
 
When you run your summary report  or dangling line report are there dangling 
lines?
If so  "in a copy database" try glossing the dangling lines have "only" line 
smoothing checked and "only" dangling lines inside line smoothing form checked.
 
Gerry
 

 Gerry Meier
Sr. PCB Designer
Freedom CAD Services, Inc.
Voice: (603) 864-1300 x1350
Alt. Voice: (386) 753-0048
Email: gerry.meier@xxxxxxxxxxxxxx
visit our website at< http://www.freedomcad.com <http://www.freedomcad.com/> 



 

  _____  

From: Van Huynh (huynh) [mailto:huynh@xxxxxxxxx] 
Sent: Saturday, December 18, 2004 12:46 PM
To: icu-pcb-forum@xxxxxxxxxxxxx
Subject: [PCB_FORUM] Re: Help!!! Segment with same start and end points 


I ran DBDoctor within the database and outside on the shell command line still 
doesn't help.
Thanks for input
 
Van Huynh

 
 

  _____  

From: Gerry Meier [mailto:gerry.meier@xxxxxxxxxxxxxx] 
Sent: Saturday, December 18, 2004 9:41 AM
To: icu-pcb-forum@xxxxxxxxxxxxx
Subject: [PCB_FORUM] Re: Help!!! Segment with same start and end points 


try running dbdoctor on the database
 

 Gerry Meier
Sr. PCB Designer
Freedom CAD Services, Inc.
Voice: (603) 864-1300 x1350
Alt. Voice: (386) 753-0048
Email: gerry.meier@xxxxxxxxxxxxxx
visit our website at< http://www.freedomcad.com <http://www.freedomcad.com/> 



 

  _____  

From: Van Huynh (huynh) [mailto:huynh@xxxxxxxxx] 
Sent: Saturday, December 18, 2004 12:37 PM
To: icu-pcb-forum@xxxxxxxxxxxxx
Subject: [PCB_FORUM] Help!!! Segment with same start and end points 


I got a lots of these warning on every artwork layers,
Any one know how to fix these errors message?
 
 WARNING: Segment with same start and end points at
 (75.2869 -194448.6314) will be ignored.  Increasing output
 accuracy may allow segment to be generated.
 
 
My artwork parameter setup:
 
DEVICE-TYPE           GERBER_RS274X
OUTPUT-UNITS          INCHES
FILM-SIZE             240000 160000
FORMAT                2.5
ABORT-ON-ERROR        NO
SCALE                 1
SUPPRESS-LEAD-ZEROES  YES
SUPPRESS-TRAIL-ZEROES NO
SUPPRESS-EQUAL        YES
UNDEF-APT-CONT        NO
 
NC Drill format is 2.5
Drawing parameter accuracy is 4
 
Thank you
Van Huynh

Other related posts: