[PCB_FORUM] Re: CDC2FAB and allegro 15.5

Thanks anyway Gerry, it the thought that counts! :-)
Dharma
 

KAW/USA Ltd. 
39 Simon Street, #4 
Nashua, NH 03060 
603-886-8711 x212 
603-881-8763 fax 

Confidentiality Notice: This email and any accompanying documents contain
information that is confidential, privileged or exempt from disclosure under
applicable law and is intended for the exclusive use of the addressee. This
information is private and protected by law. If you are not the intended
recipient, or have received this email in error, you are hereby notified
that any disclosure, copying, distribution or use of the contents of this
document in any manner is strictly prohibited.

 

  _____  

From: icu-pcb-forum-bounce@xxxxxxxxxxxxx
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of Gerry Meier
Sent: Wednesday, June 20, 2007 1:57 PM
To: icu-pcb-forum@xxxxxxxxxxxxx
Subject: [PCB_FORUM] Re: CDC2FAB and allegro 15.5



Dharma - sorry I did not read the whole email - ignore this comment

 

  _____  

From: icu-pcb-forum-bounce@xxxxxxxxxxxxx
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of Gerry Meier
Sent: Wednesday, June 20, 2007 12:49 PM
To: icu-pcb-forum@xxxxxxxxxxxxx
Subject: [PCB_FORUM] Re: CDC2FAB and allegro 15.5

 

Export the  design back to 15.5

 



 

  _____  

From: icu-pcb-forum-bounce@xxxxxxxxxxxxx
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of Dharma Kemp-Bresett
Sent: Wednesday, June 20, 2007 12:45 PM
To: icu-pcb-forum@xxxxxxxxxxxxx
Subject: [PCB_FORUM] CDC2FAB and allegro 15.5

 

Hello Again,

We seem to be beset by stumpers lately. :-)

We have been using 15.5 for some time now but apparently no-one has used any
of the version specific features until recently. Therefore, I have always
been able to open the board in 15.2 and do other things with it like run
CDC2FAB for the .cad file output for a particular customer. I received a
board from 15.5 that I cannot open in 15.2 nor can I run my CDC2FAB on it.
Being able to offer this output format is critical with this particular
customer however so far I cannot find a solution that would not require us
to purchase software that would be overkill for our needs ( we do not need
the entire fabmaster, unicam, gencad, harmony etc. program just the ability
to output the . cad file!). For this particular board we were able to
downrev to 15.2 (and run CDC2fab on that) and do not appear to have lost
anything integral but that may not be the case in the future. (In addition
to the fact that there is not much point in having to downrev all our boards
so that we might as well not even have 15.5) I have been through the pcb
forum archives, sourcelink, and cdnusers, etc. and have found nothing so far
that helps me. Has anyone else encountered this problem?

Thanks in advance,

Dharma

 

KAW/USA Ltd. 
39 Simon Street, #4 
Nashua, NH 03060 
603-886-8711 x212 
603-881-8763 fax 

Confidentiality Notice: This email and any accompanying documents contain
information that is confidential, privileged or exempt from disclosure under
applicable law and is intended for the exclusive use of the addressee. This
information is private and protected by law. If you are not the intended
recipient, or have received this email in error, you are hereby notified
that any disclosure, copying, distribution or use of the contents of this
document in any manner is strictly prohibited.

 


This correspondence and any attachments are considered confidential. If you
are not the intended recipient, please notify Freedom CAD Services, Inc.
immediately by either replying to this message or by sending an email to
operations@xxxxxxxxxxxxxx; please destroy all copies of this message and any
attachments. Thank you.

JPEG image

Other related posts: