[gptalk] Re: Deploying Software

  • From: "Hurney, Jack" <jack.hurney@xxxxxxx>
  • To: <gptalk@xxxxxxxxxxxxx>
  • Date: Wed, 24 Oct 2007 12:01:23 -0600

What I mean is,  I run into that issue and a lot of the time it's a
permission issue on the folder containing the install package.  A
related error will usually show up in Event Viewer.  Maybe one of the
other folks would know:  would the GP Modeling piece in the GPMC be any
help to troubleshoot this?  I just started looking at that and am
wondering how useful it could be.

 

-----Original Message-----
From: gptalk-bounce@xxxxxxxxxxxxx [mailto:gptalk-bounce@xxxxxxxxxxxxx]
On Behalf Of Hurney, Jack
Sent: Wednesday, October 24, 2007 11:55 AM
To: gptalk@xxxxxxxxxxxxx
Subject: [gptalk] Re: Deploying Software

Have you looked in Event Viewer > Application  and the results of
'gpresult' for anything related?

 

-----Original Message-----
From: gptalk-bounce@xxxxxxxxxxxxx [mailto:gptalk-bounce@xxxxxxxxxxxxx]
On Behalf Of Paul Snell
Sent: Wednesday, October 24, 2007 11:44 AM
To: gptalk@xxxxxxxxxxxxx
Subject: [gptalk] Re: Deploying Software

That's what I've done. I've assigned it to the OU that contains the pcs,
and
used the group, but it doesn't appear to work.


-----Original Message-----
From: gptalk-bounce@xxxxxxxxxxxxx [mailto:gptalk-bounce@xxxxxxxxxxxxx]
On
Behalf Of Nelson, Jamie R Contr 72 CS/SCBAF
Sent: 24 October 2007 18:07
To: gptalk@xxxxxxxxxxxxx
Subject: [gptalk] Re: Deploying Software

Create a GPO and in the Security Filtering section ("Scope" tab in GPMC)
replace "Authenticated Users" with your group name. Then just link it to
your domain or top-level OU and you should be good to go.

Regards,
Jamie Nelson

-----Original Message-----
From: gptalk-bounce@xxxxxxxxxxxxx [mailto:gptalk-bounce@xxxxxxxxxxxxx]
On Behalf Of Paul Snell
Sent: Wednesday, October 24, 2007 11:30 AM
To: gptalk@xxxxxxxxxxxxx
Subject: [gptalk] Deploying Software

One of our scripters has created a set of .cmd files that install
software using a customised template. If I try to run these from a
command line I get an error message saying that it can't use UNC paths,
but then starts the installation. I want to add these scripts to a GPO
so that the software only gets installed to specific pcs. I have created
a group that contains the pcs that need to have the software installed.
What is the best way to deploy?

***********************
You can unsubscribe from gptalk by sending email to
gptalk-request@xxxxxxxxxxxxx with 'unsubscribe' in the Subject field OR
by
logging into the freelists.org Web interface. Archives for the list are
available at http://www.freelists.org/archives/gptalk/
************************

***********************
You can unsubscribe from gptalk by sending email to
gptalk-request@xxxxxxxxxxxxx with 'unsubscribe' in the Subject field OR
by logging into the freelists.org Web interface. Archives for the list
are available at http://www.freelists.org/archives/gptalk/
************************
***********************
You can unsubscribe from gptalk by sending email to
gptalk-request@xxxxxxxxxxxxx with 'unsubscribe' in the Subject field OR
by logging into the freelists.org Web interface. Archives for the list
are available at http://www.freelists.org/archives/gptalk/
************************
***********************
You can unsubscribe from gptalk by sending email to 
gptalk-request@xxxxxxxxxxxxx with 'unsubscribe' in the Subject field OR by 
logging into the freelists.org Web interface. Archives for the list are 
available at http://www.freelists.org/archives/gptalk/
************************

Other related posts: