Re: [foxboro] WP70


Hope this helps

This can happen if you are loading any version software below 6.4....
As stated in document B0400RU .....Page 48.....The specific doc that ships
with the GX240 station.
After loading I/A software you must select NO to reboot and perform a
diskette task.....see excerpt from document below:

B0400RU - Rev A 2. Installing I/A Series Software
Restarting Your System
When the I/A Series software installation is complete, the setup program
asks you to reboot your
workstation as shown in Figure 2-12. Do not reboot the workstation with the
new software, select
NO, I do not want to restart my computer now in the display window and click
on Finish.
Loading the I/A Series Driver for the GX240 P93
You must perform the following procedure to allow the workstation to boot
after installing I/A.
The driver updates some I/A files required for the GX240 P93 and the
multi-port serial card to
work correctly with the I/A Series system. If the following procedure is not
performed
for I/A Series Software Version 6.3 or earlier, the system will not boot.
To load the I/A Series driver for the Multi-port Serial card and other
required files:
1. Insert the floppy disk K0175VY
2. In the Start menu, click on Run.
3. Enter: A:\setup. The files are copied.
4. If no Equinox driver you will get an error.
5. Re-boot the system.
NOTE
If the above procedure is not performed for I/A Series Version 6.3 software
or earlier
the system will not boot



>  -----Original Message-----
> From:         foxboro-bounce@xxxxxxxxxxxxx@CORP   On Behalf Of "MIKE
> KINCH" <MIKE.KINCH@xxxxxxxxxxxxxxxxxx>
> Sent: Tuesday, November 12, 2002 12:00 AM
> To:   foxboro@xxxxxxxxxxxxx
> Subject:      [foxboro] WP70
> 
> 
> Dear list,
> 
> I have replaced WP70 hardware with DELL GX 240s. After loading and after
> th=
> e first reboot I cannot get past a blue screen with the service pack
> detail=
> s. I have tried NT service pack 5 and 6 with no results.
> 
> Any ideas please.
> 
> Mike Kinch
> Sydney Water
> 
> 
> 
> -----------------------------------------------------------
> This e-mail is solely for the use of the intended recipient
> and may contain information which is confidential or
> privileged. Unauthorised use of its contents is prohibited.
> If you have received this e-mail in error, please notify=20
> the sender immediately via e-mail and then delete the=20
> original e-mail.
> -----------------------------------------------------------
> 
> 
> 
> _______________________________________________________________________
> This mailing list is neither sponsored nor endorsed by Invensys Process
> Systems (formerly The Foxboro Company). Use the info you obtain here at
> your own risks. Read http://www.thecassandraproject.org/disclaimer.html
> 
> foxboro mailing list:             http://www.freelists.org/list/foxboro
> to subscribe:         mailto:foxboro-request@xxxxxxxxxxxxx?subject=join
> to unsubscribe:      mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave
>  


-- No attachments (even text) are allowed --
-- Type: application/ms-tnef


 
 
_______________________________________________________________________
This mailing list is neither sponsored nor endorsed by Invensys Process
Systems (formerly The Foxboro Company). Use the info you obtain here at
your own risks. Read http://www.thecassandraproject.org/disclaimer.html
 
foxboro mailing list:             http://www.freelists.org/list/foxboro
to subscribe:         mailto:foxboro-request@xxxxxxxxxxxxx?subject=join
to unsubscribe:      mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave

Other related posts: