Re: [foxboro] MICRO-I/A with NBI don´t boot


What letterbug are you using in the DNBI?  It should most likely be a "=
CA"
or "CB".  Ours is a "CA".  Also, I seem to remember some past discussio=
ns
that not all hubs are compatible with the Foxboro communications.  We a=
re
using the Centricom that was recommend by Foxboro.

Neil Martin
Huntsman Corporation
7114 North Lamar Blvd
Austin, TX.  78752
ph) 512-483-0119


                                                                       =
                                        =20
                    "Bismarck Alban"                                   =
                                        =20
                    <balban@tecniequip       To:     <foxboro@freelists=
.org>                                   =20
                    os.com>                  cc:                       =
                                        =20
                    Sent by:                 Subject:     Re: [foxboro]=
 MICRO-I/A with NBI don=B4t boot          =20
                    foxboro-bounce@fre                                 =
                                        =20
                    elists.org                                         =
                                        =20
                                                                       =
                                        =20
                                                                       =
                                        =20
                    11/26/02 10:30 AM                                  =
                                        =20
                    Please respond to                                  =
                                        =20
                    foxboro                                            =
                                        =20
                                                                       =
                                        =20
                                                                       =
                                        =20





Hi List

I was trying to install one Micro I/A type 1 station in a system with A=
W51D
host station, with 3 CP30s, and two WP51D, all under I/A Nodebus
ver.6.2.1(UNIX) and hosted by the AW51D.
I used an NBI connected to AUI port of one Hub (across Nodebus Transcei=
ver)
and ethernet cable to a Micro I/A.
I load a commited diskette with the new station and the Upload Server
diskette.
When Micro I/A is reseted, the red led turn on about 15 seconds, then b=
oth,
red and green turn on and also the ethernet indicator, about 30 seconds=
 the
ethernet led goes off about half of seconds and turns on again, and it
repeat for always.
In the SMDH appear the Micro I/A as red station (failed)
In the Lbug Map program, there doesn=B4t appear the Micro I/A serial nu=
mber,
it=B4s unactive the Unbooted Stations button.

Thanks in advance and best regards



Bismarck Alban
Tecniequipos S.A.
Quito-Ecuador
poh.(593)2-2462072, (593)2-2462074, (593)2-2449624
fax.  (593)2-2449625



_______________________________________________________________________=

This mailing list is neither sponsored nor endorsed by Invensys Process=

Systems (formerly The Foxboro Company). Use the info you obtain here at=

your own risks. Read http://www.thecassandraproject.org/disclaimer.html=


foxboro mailing list:             http://www.freelists.org/list/foxboro=

to subscribe:         mailto:foxboro-request@xxxxxxxxxxxxx?subject=3Djo=
in
to unsubscribe:      mailto:foxboro-request@xxxxxxxxxxxxx?subject=3Dlea=
ve



=


 
 
_______________________________________________________________________
This mailing list is neither sponsored nor endorsed by Invensys Process
Systems (formerly The Foxboro Company). Use the info you obtain here at
your own risks. Read http://www.thecassandraproject.org/disclaimer.html
 
foxboro mailing list:             http://www.freelists.org/list/foxboro
to subscribe:         mailto:foxboro-request@xxxxxxxxxxxxx?subject=join
to unsubscribe:      mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave
 

Other related posts: