Re: [foxboro] How to move a FCP online from one Switch to another Switch?

You should also consider aging time of the IP address in the switches. This is 
300 seconds as default. So don't pull the second fibre pair too quickly. You 
also can't trust the info given by system management in this one. So the safest 
operation is to wait at least the standard aging time. Personally I would 
double or triple that time, just to be sure.



Met vriendelijke groet / Best regards,



Walter Dixon
Saint-Gobain Isover Benelux B.V.
Industriële Automatisering
Email:  walter.dixon@xxxxxxxxxxxxxxxx
Tel:    +31 (0) 76 50 80 457
Fax:    +31 (0) 76 50 80 335
Internet:       http://www.isover.nl

 Please consider your environmental responsibility before printing this e-mail 

Deze e-mail en bijlagen bij deze e-mail zijn uitsluitend bestemd voor de door 
de afzender vermelde geadresseerde(n). Indien deze e-mail inclusief bijlagen 
niet voor u bestemd is, verzoeken wij u vriendelijk die onmiddellijk te 
verwijderen, de ontvangst ervan onmiddellijk telefonisch (+31 (0)76-5080 000) 
aan ons te melden en de inhoud ervan niet aan anderen bekend te maken. 
Bekendmaking en gebruik van de inhoud van deze e-mail en bijlagen bij deze 
e-mail zonder toestemming van de afzender of de door de afzender beoogde 
geadresseerde kan onrechtmatig zijn. Saint-Gobain Isover Benelux B.V. is een 
besloten vennootschap naar Nederlands recht en statutair gevestigd in 
Etten-Leur en ingeschreven in het handelsregister onder nummer 20022420. Op 
iedere rechtsbetrekking tussen Saint-Gobain Isover Benelux B.V. en derden zijn 
toepasselijk de algemene inkoopvoorwaarden van Saint-Gobain Isover Benelux B.V. 
zoals op 22 mei 2007 gedeponeerd bij de rechtbank ’s Hertogenbosch onder 
depotnummer 41/2007. Indien een digitale versie toegestuurd wenst te krijgen 
dan kan u zich richten tot onze afdeling inkoop op tel: +31-76-5080284. De 
toepasselijkheid van andere algemene voorwaarden wordt uitdrukkelijk van de 
hand gewezen. 

-----Oorspronkelijk bericht-----
Van: foxboro-bounce@xxxxxxxxxxxxx [mailto:foxboro-bounce@xxxxxxxxxxxxx] Namens 
Boulay, Russ
Verzonden: donderdag 22 januari 2009 18:49
Aan: foxboro@xxxxxxxxxxxxx
Onderwerp: Re: [foxboro] How to move a FCP online from one Switch to another 
Switch?


Andreas,
FT FCP270 connected to two switches.
Remember cables from a FT FCP270 are thru a splitter/combiner.

When you remove first FCP cable from first switch, that cable is a
combination of both FCP's A cable.
So the FCP270 pair switches to it's B connection to Mesh.
Both FCP's stay running.

Connect A to new switch. So now A cable on new switch B cable on old.
FCP270 then recovers communication on A and auto switches back to A
ports/switch.

Duplicate same move as above for B connection...

You should never have Single FCP270..during above procedure..it should
mainatin FT operation.


-----Original Message-----
From: foxboro-bounce@xxxxxxxxxxxxx [mailto:foxboro-bounce@xxxxxxxxxxxxx]
On Behalf Of Weiss, Andreas
Sent: Thursday, January 22, 2009 09:22 AM
To: foxboro@xxxxxxxxxxxxx
Subject: [foxboro] How to move a FCP online from one Switch to another
Switch?

Dear experts,

what's the best way to move a FCP270 online from one switch to another?

Online means that an Operator on a AW should be able to see all Object
Manager / Compound:Block.Parameter values hosted on that FCP.

a scenario could be:

= redundant connection
- single connection


step 1 "current situation"

                                +==>ATS<==>NCNI<==>Switch<==>RCNI<==>AW
on the Nodebus
                                |
AW on the Mesh <==> Root-Switch <==>SW<===>FCP


step 2 "remove the connection from the FCP to one of the two redundant
switches"


                                +==>ATS<==>NCNI<==>Switch<==>RCNI<==>AW
on the Nodebus
                                |
AW on the Mesh <==> Root-Switch <==>SW<--->FCP


step 3 "connect the FCP to another switch"

                                +==>ATS<==>NCNI<==>Switch<==>RCNI<==>AW
on the Nodebus
                                |
AW on the Mesh <==> Root-Switch <==>SW<--->FCP
                          +                 |
                          |-----------------|


step 4 "move the other connection the other switch"


                                +==>ATS<==>NCNI<==>Switch<==>RCNI<==>AW
on the Nodebus
                                |
AW on the Mesh <==> Root-Switch <==>SW
                          +                 
                          |<==============>FCP


step 5 "reset the failed FCP module so that it marries again"

Is it possible and supported to do that?

Regards,
Andreas
 
 
_______________________________________________________________________
This mailing list is neither sponsored nor endorsed by Invensys Process
Systems (formerly The Foxboro Company). Use the info you obtain here at
your own risks. Read http://www.thecassandraproject.org/disclaimer.html
 
foxboro mailing list:             http://www.freelists.org/list/foxboro
to subscribe:         mailto:foxboro-request@xxxxxxxxxxxxx?subject=join
to unsubscribe:      mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave
 


* Confidentiality Notice:
This e-mail and any associated files are intended solely for the individual or 
entity to whom they are addressed. Please do not copy it or use it for any 
purposes, or disclose its contents to any other person. Further, this e-mail 
and any associated files may be confidential and further may be legally 
privileged. This email is from the Invensys Process Systems business unit of 
Invensys plc which is a company registered in England and Wales with its 
registered office at Portland House, Bressenden Place, London, SW1E 5BF 
(Registered number 166023).  For a list of European legal entities within the 
Invensys Process Systems business group, please click here 
http://www.invensys.com/legal/default.asp?top_nav_id=77&nav_id=80&prev_id=77.

If you have received this e-mail in error, you are on notice of its status. 
Please notify us immediately by reply e-mail and then delete this message from 
your system. Thank you for your co-operation. You may contact our Helpdesk on 
+44 (0)20 7821 3859 / 2105 or email inet.hqhelpdesk@xxxxxxxxxxxxx This e-mail 
and any attachments thereto may be subject to the terms of any agreements 
between Invensys (and/or its subsidiaries and affiliates) and the recipient 
(and/or its subsidiaries and affiliates).


 
 
_______________________________________________________________________
This mailing list is neither sponsored nor endorsed by Invensys Process
Systems (formerly The Foxboro Company). Use the info you obtain here at
your own risks. Read http://www.thecassandraproject.org/disclaimer.html
 
foxboro mailing list:             http://www.freelists.org/list/foxboro
to subscribe:         mailto:foxboro-request@xxxxxxxxxxxxx?subject=join
to unsubscribe:      mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave
 
 
 
_______________________________________________________________________
This mailing list is neither sponsored nor endorsed by Invensys Process
Systems (formerly The Foxboro Company). Use the info you obtain here at
your own risks. Read http://www.thecassandraproject.org/disclaimer.html
 
foxboro mailing list:             http://www.freelists.org/list/foxboro
to subscribe:         mailto:foxboro-request@xxxxxxxxxxxxx?subject=join
to unsubscribe:      mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave

Other related posts: