Re: [foxboro] FDSI driver AB CSP or FDSI Driver Ethernet/IP
- From: "Wilson, Brad" <brad.wilson@xxxxxxxxxxxx>
- To: "'foxboro@xxxxxxxxxxxxx'" <foxboro@xxxxxxxxxxxxx>
- Date: Fri, 1 Oct 2010 22:17:55 -0400
I think you can bitmap the IIN.LIN value to the MCOUTs. If so, you can
eliminate the 1st MCIN. Of course if you're able to modify you graphics/control
blocks, you can map them all to the IINs (if it works, of course)
--------------------------
Sent from my BlackBerry Wireless Device
----- Original Message -----
From: Tadeo Armenta [mailto:tadeoarmenta@xxxxxxxxx]
Sent: Friday, October 01, 2010 09:37 PM
To: foxboro@xxxxxxxxxxxxx <foxboro@xxxxxxxxxxxxx>
Subject: Re: [foxboro] FDSI driver AB CSP or FDSI Driver Ethernet/IP
Yes brad,
PACKIN solution is what you said.
for I and O registers I used 2 IIN blocks, conected to a MCIN, then I mapped
the bits using a pair of MCOUT blocks and finally rejoined them in the final
MCIN.
So... 6 blocks to read 2 16 bit registers... thank god there are taglists...
even if they are not that friendly user as they should
________________________________
De: "Wilson, Brad" <brad.wilson@xxxxxxxxxxxx>
Para: "foxboro@xxxxxxxxxxxxx" <foxboro@xxxxxxxxxxxxx>
Enviado: vie, octubre 1, 2010 2:36:10 AM
Asunto: Re: [foxboro] FDSI driver AB CSP or FDSI Driver Ethernet/IP
No, I'm sorry to say that .WM is not supported in CSP or DH+. Not having a
system I can test it on, my "thought experiment" would lead me to try 2 PAKIN
blocks, each reading consecutive 16-bit words with the /U2 option and PKIOPT=3
to reverse the bits. Then connect those 2 PAKCIN's to II01 and II02 of a MCIN.
The PAKCIN of the MCIN should be what your looking for. (My head hurts from
trying to mentally work thru that.)
If you're trying to read I or O registers, try the same thing with IIN instead
of PAKIN and connect the LIN's. (That may not work though, because I don't
think
/U2 works on I & O values.)
If none of that works, then brute force may be your only option ... reading
32-bits with a PAKIN and mapping each bit in reverse order (1-16 into 16-1 and
17-32 into 32-17) into a PAKOUT that is either configured to write to a "safe"
register or is configured to a "dummy" ECB that is off-line. I think the values
will still propogate, even though the block will show bad IO.
Good luck.
Brad Wilson
Invensys Operations Management
NA Northeast Service
________________________________________
From: foxboro-bounce@xxxxxxxxxxxxx [foxboro-bounce@xxxxxxxxxxxxx] On Behalf Of
Kevin Fitzgerrell [fitzgerrell@xxxxxxxxx]
Sent: Thursday, September 30, 2010 8:12 PM
To: foxboro@xxxxxxxxxxxxx
Subject: Re: [foxboro] FDSI driver AB CSP or FDSI Driver Ethernet/IP
Brad,
That is what we need in all the AB FDSI drivers. I saw that in the
EthernetIP manual you've referenced. I don't see it documented for the CSP
or DH+ driver - can you confirm this is available in those?
Regards,
Kevin
On Fri, Oct 1, 2010 at 12:58 AM, Wilson, Brad <brad.wilson@xxxxxxxxxxxx>wrote:
> Using the :WM option on the PKINGP parameter doesn't work? That seems to be
> what it is designed for ... bit-mirroring each 16-bit word (Fig 3-8 of
> B0700BU_B).
>
> "what i need is something that flips the first 16 bits, and then flips the
> second 16 bits"
>
> Brad Wilson
> Invensys Operations Management
> NA Northeast Service
*** Confidentiality Notice: This e-mail, including any associated or attached
files, is intended solely for the individual or entity to which it is
addressed.
This e-mail is confidential and may well also be legally privileged. If you
have
received it in error, you are on notice of its status. Please notify the sender
immediately by reply e-mail and then delete this message from your system.
Please do not copy it or use it for any purposes, or disclose its contents to
any other person. This email comes from a division of the Invensys Group, owned
by Invensys plc, which is a company registered in England and Wales with its
registered office at 3rd Floor, 40 Grosvenor Place, London, SW1X 7AW
(Registered
number 166023). For a list of European legal entities within the Invensys
Group,
please go to
http://www.invensys.com/legal/default.asp?top_nav_idw&nav_id€&prev_idw.
You may contact Invensys plc on +44 (0)20 3155 1200 or e-mail
reception@xxxxxxxxxxxxx This e-mail and any attachments thereto may be subject
to the terms of any agreements between Invensys (and/or its subsidiaries and
affiliates) and the recipient (and/or its subsidiaries and affiliates).
_______________________________________________________________________
This mailing list is neither sponsored nor endorsed by Invensys Process
Systems (formerly The Foxboro Company). Use the info you obtain here at
your own risks. Read http://www.thecassandraproject.org/disclaimer.html
foxboro mailing list: //www.freelists.org/list/foxboro
to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join
to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave
_______________________________________________________________________
This mailing list is neither sponsored nor endorsed by Invensys Process
Systems (formerly The Foxboro Company). Use the info you obtain here at
your own risks. Read http://www.thecassandraproject.org/disclaimer.html
foxboro mailing list: //www.freelists.org/list/foxboro
to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join
to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave
*** Confidentiality Notice: This e-mail, including any associated or attached
files, is intended solely for the individual or entity to which it is
addressed. This e-mail is confidential and may well also be legally privileged.
If you have received it in error, you are on notice of its status. Please
notify the sender immediately by reply e-mail and then delete this message from
your system. Please do not copy it or use it for any purposes, or disclose its
contents to any other person. This email comes from a division of the Invensys
Group, owned by Invensys plc, which is a company registered in England and
Wales with its registered office at 3rd Floor, 40 Grosvenor Place, London, SW1X
7AW (Registered number 166023). For a list of European legal entities within
the Invensys Group, please go to
http://www.invensys.com/legal/default.asp?top_nav_id=77&nav_id=80&prev_id=77.
You may contact Invensys plc on +44 (0)20 3155 1200 or e-mail
reception@xxxxxxxxxxxxx This e-mail and any attachments thereto may be subject
to the terms of any agreements between Invensys (and/or its subsidiaries and
affiliates) and the recipient (and/or its subsidiaries and affiliates).
_______________________________________________________________________
This mailing list is neither sponsored nor endorsed by Invensys Process
Systems (formerly The Foxboro Company). Use the info you obtain here at
your own risks. Read http://www.thecassandraproject.org/disclaimer.html
foxboro mailing list: //www.freelists.org/list/foxboro
to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join
to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave
Other related posts:
