Try it with a iin block for a single 16 bit register, if you can read try to do a swap f4:w3 for example. Angel Dominguez 938 136-8842 -----Original Message----- From: RAKESH DASH Sent: 01/07/2012, 14:47 To: foxboro@xxxxxxxxxxxxx Subject: Re: [foxboro] FBM231 RS485 COMMUNICATION Angel/Sahara, Yes, I have 43001:F4. Sorry I mistyped it. There are three different types of devices communicating. Port1 and Port2 device are fine and data also is received. The device which is a electric meter & connected to Port3 is unable to communicate. Rather in SMDH it shows me healthy if I don't configure any points in IACC. As soon as I configure a floating point, & download, the SMDH says "Device Failed". So not sure what I am missing. Gerrit has suggested few things to check which I will try. Any other help on the subject is appreciated Thanks !! - Rakesh On Sun, Jul 1, 2012 at 9:49 PM, Dominguez, Angel < angel.dominguez@xxxxxxxxxxxx> wrote: > There's two address format 5 or 6 digits, you should have 43001:F4 as a > valid format. > Angel Dominguez > 938 136-8842 > -----Original Message----- > From: שחר קצב > Sent: 01/07/2012, 11:16 > To: foxboro@xxxxxxxxxxxxx > Subject: Re: [foxboro] FBM231 RS485 COMMUNICATION > > Hi, does the problem is that you can't configure all the ports? > Shahar chemada fine chemicals > > -----Original Message----- > From: foxboro-bounce@xxxxxxxxxxxxx [mailto:foxboro-bounce@xxxxxxxxxxxxx] > On Behalf Of RAKESH DASH > Sent: Saturday, June 30, 2012 8:53 PM > To: foxboro@xxxxxxxxxxxxx > Subject: [foxboro] FBM231 RS485 COMMUNICATION > > Hi there, > I am trying to interface FBM231 with an external device over RS485. > The modbus data is Holding Register Floating Point (4 bytes) > I checked the communication and data using modscan in a laptop and all is > good. > The configuration in FDSI baud rate etc. is also fine > > FBM231 is showing healthy on communication. > But As soon as I define even one signal in the RIN block in the compound > for receiving the data & download, the FBM231 goes out of order and shows > me as device failed. > I have configured the point address PNT_NO as 430001:F4. > > I there any known issue of such kind ? Does the FBM231 support floating > point signals ? > I am stuck with this and I have to wind this up by Tuesday. Any help on the > subject is appreciated. Thanks !! > > Regards, > - Rakesh > > > > > _______________________________________________________________________ > This mailing list is neither sponsored nor endorsed by Invensys Process > Systems (formerly The Foxboro Company). Use the info you obtain here at > your own risks. Read http://www.thecassandraproject.org/disclaimer.html > > foxboro mailing list: //www.freelists.org/list/foxboro > to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join > to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave > > > > _______________________________________________________________________ > This mailing list is neither sponsored nor endorsed by Invensys Process > Systems (formerly The Foxboro Company). Use the info you obtain here at > your own risks. Read http://www.thecassandraproject.org/disclaimer.html > > foxboro mailing list: //www.freelists.org/list/foxboro > to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join > to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave > > > > *** Confidentiality Notice: This e-mail, including any associated or > attached files, is intended solely for the individual or entity to which it > is addressed. This e-mail is confidential and may well also be legally > privileged. If you have received it in error, you are on notice of its > status. Please notify the sender immediately by reply e-mail and then > delete this message from your system. Please do not copy it or use it for > any purposes, or disclose its contents to any other person. This email > comes from a division of the Invensys Group, owned by Invensys plc, which > is a company registered in England and Wales with its registered office at > 3rd Floor, 40 Grosvenor Place, London, SW1X 7AW (Registered number 166023). > For a list of European legal entities within the Invensys Group, please go > to http://www.invensys.com/en/legal/default.aspx. > > You may contact Invensys plc on +44 (0)20 3155 1200 or e-mail > reception@xxxxxxxxxxxxx This e-mail and any attachments thereto may be > subject to the terms of any agreements between Invensys (and/or its > subsidiaries and affiliates) and the recipient (and/or its subsidiaries and > affiliates). > > > > > _______________________________________________________________________ > This mailing list is neither sponsored nor endorsed by Invensys Process > Systems (formerly The Foxboro Company). Use the info you obtain here at > your own risks. Read http://www.thecassandraproject.org/disclaimer.html > > foxboro mailing list: //www.freelists.org/list/foxboro > to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join > to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave > > _______________________________________________________________________ This mailing list is neither sponsored nor endorsed by Invensys Process Systems (formerly The Foxboro Company). Use the info you obtain here at your own risks. Read http://www.thecassandraproject.org/disclaimer.html foxboro mailing list: //www.freelists.org/list/foxboro to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave *** Confidentiality Notice: This e-mail, including any associated or attached files, is intended solely for the individual or entity to which it is addressed. This e-mail is confidential and may well also be legally privileged. If you have received it in error, you are on notice of its status. Please notify the sender immediately by reply e-mail and then delete this message from your system. Please do not copy it or use it for any purposes, or disclose its contents to any other person. This email comes from a division of the Invensys Group, owned by Invensys plc, which is a company registered in England and Wales with its registered office at 3rd Floor, 40 Grosvenor Place, London, SW1X 7AW (Registered number 166023). For a list of European legal entities within the Invensys Group, please go to http://www.invensys.com/en/legal/default.aspx. You may contact Invensys plc on +44 (0)20 3155 1200 or e-mail reception@xxxxxxxxxxxxx This e-mail and any attachments thereto may be subject to the terms of any agreements between Invensys (and/or its subsidiaries and affiliates) and the recipient (and/or its subsidiaries and affiliates). _______________________________________________________________________ This mailing list is neither sponsored nor endorsed by Invensys Process Systems (formerly The Foxboro Company). Use the info you obtain here at your own risks. Read http://www.thecassandraproject.org/disclaimer.html foxboro mailing list: //www.freelists.org/list/foxboro to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave