Re: [foxboro] Communication problem b/w FBM231 & AB PLC

Dear Scott,
I have that document and I followed that and switch setting which you
provide does not work and we don't know the modem numebr but the modem is
also of AB and AB PLC is PLC 5/40 and it is connect to CAM or Modem by DH+,

and we configured the .XML file as

Port 1
Mode= RS-232
Baud Rete=9600
Parity= none
stop bits=1
databits=8
driver=DHPlus/CRC

Kindly guide me.

Thanks and Rgds
Imran Butt.


On 9/12/07, Imran Waheed Butt <butt.imran@xxxxxxxxx> wrote:
>
> Does any one has DI700BD document, if yes kindly e-mail me on my e-mail
> address,
>
> Rgds,
> Imran Butt.
>
>
>  On 9/12/07, Landry, Scott <scott.landry@xxxxxxxxxxxxxxxx> wrote:
> >
> > Imran,
> >
> >
> > Are you using direct connect, AB1785KE or AB-KF2 ?
> >
> > As far as I know the direct connect method is not supported.
> >
> > AB1785KE is:
> >
> > A2,A4,A6,A8 --- B8 ---  C1,C4,C5  closed  (all others open)
> >
> > AB-KF2 is:
> >
> > A2,A4,A6,A8 --- B8 ---  C1 and C5  closed  (all others open)
> >
> >
> > Please refer to DI700BD  FDSI Driver Allen Bradley DH+ Protocol
> >
> >
> > Regards,
> >
> >
> >   Scott L. Landry
> >   Invensys Process Systems/Foxboro
> >   Gulf Coast Region  USA
> >
> >
> >
> > -----Original Message-----
> > From: foxboro-bounce@xxxxxxxxxxxxx [mailto:foxboro-bounce@xxxxxxxxxxxxx]
> > On=
> > Behalf Of Imran Waheed Butt
> > Sent: Wednesday, September 12, 2007 3:39 AM
> > To: foxboro@xxxxxxxxxxxxx
> > Subject: Re: [foxboro] Communication problem b/w FBM231 & AB PLC
> >
> > Sorry that is DI15
> > On 9/12/07, Imran Waheed Butt <butt.imran@xxxxxxxxx > wrote:
> > >
> > > Dear Kevin,
> > >
> > > Sorry there there was not MG30 that is COMM15 we were using now that
> > is
> > > replaced by FBM231.
> > >
> > > Thanks and Regards,
> > > Imran
> > >
> > >
> > >  On 9/12/07, Kevin Fitzgerrell <fitzgerrell@xxxxxxxxx> wrote:
> > > >
> > > > Imran,
> > > >
> > > > How are you using an MG30 to communicate with an AB PLC?  Are you
> > > > using a Prosoft card?
> > > >
> > > > Regards,
> > > >
> > > > Kevin FitzGerrell
> > > >
> > > > On 9/12/07, Imran Waheed Butt <butt.imran@xxxxxxxxx > wrote:
> > > > > Dear All,
> > > > > Our customer is upgrading the I/A version form V4.3 Unix to V8.2on X=
> > P
> > > > and
> > > > > previous system has CP30FT communicating with 100 series FBMs and
> > FBC=
> > s
> > > > and
> > > > > quantity 3 MG30 gateways communicating with Allen Bradley PLC
> > through=
> >
> > > > CAM or
> > > > > Modem which is provided by Allen Bradley.
> > > > >
> > > > > The CP30FT is upgraded to FCP270FT and 100 series FBM and FBC are
> > > > remain
> > > > > same.
> > > > >
> > > > > The 3 no. MG30 are replaced by and other FCP270FT with FBM231
> > (FT).
> > > > >
> > > > >  I am at the commissioning/installation of the system and facing
> > > > following
> > > > > problems,
> > > > >
> > > > >   1.  FBM231 is not communicating with AB PLC through CAM or Modem
> > as=
> >
> > > > we
> > > > >   translate the same DIP switch setting which is on the P0970VN
> > (MG30=
> >
> > > > >   configuration selection switch) to the FBM231 TA, the switch
> > > > settings are
> > > > >   as,
> > > > >   MG30>>>         SW1-1,2,3,4,7,8 & SW2-1,3,4,6,8 are closed and
> > > > >   remaining are open
> > > > >   we translate them form documents B0193RL-Rev H page 49-50 and
> > form
> > > > >   B0700AH Rev E page 62-63 and translated switch setting are as,
> > > > >   FBM231 TA>>>             A-2,4,6,8 & B-4,8 & C-1 are close and
> > > > >   remaining are open.
> > > > >   But it is not communicating with PLC.
> > > > >   2. The cable part number which is connecting PLC to Gateway is
> > > > >   P0970WY-C and we are using the same cable.
> > > > >   3. Previously AIN, AOUT, CIN and COUT blocks are in the database
> > of=
> >
> > > > >   MG30 which communicate with PLC, and now these blocks we can't
> > use
> > > > with
> > > > >   FBM231 to communicate with PLC so, we create RIN, ROUT, BIN and
> > BOU=
> > T
> > > > blocks
> > > > >   and connect the out put of these blocks to the input of AIN and
> > CIN=
> >
> > > > and
> > > > >   output of COUT and AOUT to input of BOUT and ROUT.
> > > > >   Now problem is that the previous addressing of PNT parameter of
> > CIN=
> >
> > > > is
> > > > >   and COUT are like 4.12:0 and 16.15:0 and for AIN and AOUT have
> > like=
> >
> > > > >   126:0 at their PNT parameter. Kindly guide me how to translate
> > the
> > > > above
> > > > >   format to PNT parameter to the format of BIN,BOUT, RIN and ROUT.
> > > > >   We copy the same PNT no. to the PNT of BIN, BOUT, RIN, ROUT's
> > PNT
> > > > but
> > > > >   when loaded to FCP it gives error W65.
> > > > >
> > > > > Kindly all the experts provide me solution of above issues.
> > > > >
> > > > >
> > > > >
> > > > > Thanks and Best Regards,
> > > > >
> > > > > Imran Butt,
> > > > >
> > > > > System Engineer,
> > > > >
> > > > > Manstock.
> > > > >
> > > > >
> > > >
> > > >
> > > >
> > _______________________________________________________________________=
> >
> > > > This mailing list is neither sponsored nor endorsed by Invensys
> > Process=
> >
> > > > Systems (formerly The Foxboro Company). Use the info you obtain here
> > at=
> >
> > > > your own risks. Read
> > http://www.thecassandraproject.org/disclaimer.html=
> >
> > > >
> > > > foxboro mailing list:
> > http://www.freelists.org/list/foxboro=
> >
> > > > to subscribe:         mailto:
> > foxboro-request@xxxxxxxxxxxxx?subject=3Dj=<http://foxboro-request@xxxxxxxxxxxxx/?subject=3Dj=>
> > oin
> > > > to unsubscribe:      mailto:foxboro-request@xxxxxxxxxxxxx
> > ?subject=3Dlea=
> > ve
> > > >
> > > >
> > >
> > >
> > > --
> > > Thanks and Best Regards,
> > > Imran Butt
> > > System Engineer
> > > Manstock Engineering Company (Pvt.) Ltd.
> > > 39-42 Farid Chambers, Abdullah Haroon Road
> > > Karachi =E2=80=93 74400, Pakistan
> > > Cell: +92-321-2102686
> > > Home: +92-21-4590568
> > > Office: +92-21-5678952, 5678953, 5673145
> > > FAX: +92-21-5682576
> > > E-mail: butt.imran@xxxxxxxxx
> > > URL: http://www.manstock-engg.com
> >
> >
> >
> >
> > -- =
> >
> > Thanks and Best Regards,
> > Imran Butt
> > System Engineer
> > Manstock Engineering Company (Pvt.) Ltd.
> > 39-42 Farid Chambers, Abdullah Haroon Road
> > Karachi =E2=80=93 74400, Pakistan
> > Cell: +92-321-2102686
> > Home: +92-21-4590568
> > Office: +92-21-5678952, 5678953, 5673145
> > FAX: +92-21-5682576
> > E-mail: butt.imran@xxxxxxxxx
> > URL: http://www.manstock-engg.com
> >
> > =
> >
> > =
> >
> > _______________________________________________________________________
> > This mailing list is neither sponsored nor endorsed by Invensys Process
> > Systems (formerly The Foxboro Company). Use the info you obtain here at
> > your own risks. Read http://www.thecassandraproject.org/disclaimer.html
> > =
> >
> > foxboro mailing list:             http://www.freelists.org/list/foxboro
> > to subscribe:         mailto:foxboro-request@xxxxxxxxxxxxx
> > ?subject=3Djoin
> > to unsubscribe:      mailto:foxboro-request@xxxxxxxxxxxxx
> > ?subject=3Dleave
> > =
> >
> >
> >
> > Confidentiality Notice:
> > This e-mail and any associated files are intended solely for the
> > individual=
> > or entity to whom they are addressed. Please do not copy it or use it
> > for =
> > any purposes, or disclose its contents to any other person. Further,
> > this e=
> > -mail and any associated files may be confidential and further may be
> > legal=
> > ly privileged. This email is from the Invensys Process Systems business
> > uni=
> > t of Invensys plc which is a company registered in England and Wales
> > with i=
> > ts registered office at Portland House, Bressenden Place, London, SW1E
> > 5BF =
> > (Registered number 166023).  For a list of European legal entities
> > within t=
> > he Invensys Process Systems business group, please click here
> > http://www.in=
> > vensys.com/legal/default.asp?top_nav_id=3D77&nav_id=3D80&prev_id=3D77.
> >
> > If you have received this e-mail in error, you are on notice of its
> > status.=
> > Please notify us immediately by reply e-mail and then delete this
> > message =
> > from your system. Thank you for your co-operation. You may contact our
> > Help=
> > desk on +44 (0)20 7821 3859 / 2105 or email inet.hqhelpdesk@xxxxxxxxxxxxx
> > T=
> > his e-mail and any attachments thereto may be subject to the terms of
> > any a=
> > greements between Invensys (and/or its subsidiaries and affiliates) and
> > the=
> > recipient (and/or its subsidiaries and affiliates).
> >
> >
> >
> >
> > _______________________________________________________________________
> > This mailing list is neither sponsored nor endorsed by Invensys Process
> > Systems (formerly The Foxboro Company). Use the info you obtain here at
> > your own risks. Read http://www.thecassandraproject.org/disclaimer.html
> >
> > foxboro mailing list:             http://www.freelists.org/list/foxboro
> > to subscribe:         mailto: foxboro-request@xxxxxxxxxxxxx?subject=join
> > to unsubscribe:      mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave
> >
> >


 
 
_______________________________________________________________________
This mailing list is neither sponsored nor endorsed by Invensys Process
Systems (formerly The Foxboro Company). Use the info you obtain here at
your own risks. Read http://www.thecassandraproject.org/disclaimer.html
 
foxboro mailing list:             http://www.freelists.org/list/foxboro
to subscribe:         mailto:foxboro-request@xxxxxxxxxxxxx?subject=join
to unsubscribe:      mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave

Other related posts: