Re: [foxboro] AW51E - Second Ethernet Card

This may help

Configuring the second Ethernet ports


For AP/AW 51B series/

Modify the following files:

/etc/inet/hosts or /etc/hosts (if possible) to have the IP address and
the logical name of the port.
/etc/hostname.le0 (the station letter bug ex. 02AP01)
/etc/hostname.le1 (the logical name of the port ex. AP51_CCR_EXPERT)

Issue the following commands:

Ifconfig le1 down=20
Ifconfig le1 unplumb
Ifconfig le1 plump
Ifconfig le1 (the IP Address given) up=20

For AP/AW 51E series/

Modify the following files:

/etc/inet/hosts or /etc/hosts (if possible) to have the IP address and
the logical name of the port.
/etc/hostname.hme0 (the station letter bug ex. 02AP01)
/etc/hostname.hme1 (the logical name of the port ex. AP51_CCR_EXPERT)

Issue the following commands:

Ifconfig hme1 down=20
Ifconfig hme1 unplumb
Ifconfig hme1 plump
Ifconfig hme1 (the IP Address given) up

-----Original Message-----
From: foxboro-bounce@xxxxxxxxxxxxx [mailto:foxboro-bounce@xxxxxxxxxxxxx]
On Behalf Of Ajit.S.Kumar@xxxxxxxxxxxxx
Sent: Monday, August 27, 2007 5:36 PM
To: foxboro@xxxxxxxxxxxxx
Cc: Ajit.S.Kumar@xxxxxxxxxxxxx
Subject: [foxboro] AW51E - Second Ethernet Card

We have a AW51E installed few years back but the second ethernet Port
were=20
never used,But
now we have to connect the same to a CISCO 3550 series switch, where all

the other PLANT wide Stations WP,AW,AP stations are connected.
However I am not able to Ping to the same port or to any other stations.

For your Info.we are using DNBT to connect to Nodebus also
ping B2AW11hme1 - message as below

ICMP Host Unreachable from gateway B2AW11 (151.128.17.201)
for icmp from B2AW11 (151.128.17.201) to b2aw11hme1 (192.69.11.163)

All the related files are updated as below

Example:  /etc/hosts     secondport 192.69.11.163
Example:  /etc/hostname.hme2  secondport

OK show-devs=20
/pci@1f,4000/SUNW,hme@2,1

Ethernet FCode selftest Diagnostic done
Hme register test -- succeeded
Internal loopback test -- succeeded
Transceiver check -- Link up

ifconfig -a  does not show 2 ethernet ports.

lo0: flags=3D849<UP,LOOPBACK,RUNNING,MULTICAST> mtu 8232
        inet 127.0.0.1 netmask ff000000=20
hme0: flags=3D863<UP,BROADCAST,NOTRAILERS,RUNNING,MULTICAST> mtu 1500
        inet 151.128.17.201 netmask ffff0000 broadcast 151.128.255.255
        ether 8:0:20:8f:18:31=20

Card used SUN Part#501-4359 ( Fast Ethernet PCI Adapter).

Checks done to confirm=20
1.Ethernet Cable replaced
2.Card tested in our DCS Lab working fine, able to ping.


Thanks & regards

Ajit - SAMREF ,SA



=20
=20
_______________________________________________________________________
This mailing list is neither sponsored nor endorsed by Invensys Process
Systems (formerly The Foxboro Company). Use the info you obtain here at
your own risks. Read http://www.thecassandraproject.org/disclaimer.html
=20
foxboro mailing list:             http://www.freelists.org/list/foxboro
to subscribe:         =
mailto:foxboro-request@xxxxxxxxxxxxx?subject=3Djoin
to unsubscribe:      =
mailto:foxboro-request@xxxxxxxxxxxxx?subject=3Dleave
=20
 
 
_______________________________________________________________________
This mailing list is neither sponsored nor endorsed by Invensys Process
Systems (formerly The Foxboro Company). Use the info you obtain here at
your own risks. Read http://www.thecassandraproject.org/disclaimer.html
 
foxboro mailing list:             http://www.freelists.org/list/foxboro
to subscribe:         mailto:foxboro-request@xxxxxxxxxxxxx?subject=join
to unsubscribe:      mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave

Other related posts: