[duxhelp] Re: another graphics issue

  • From: "Peter Sullivan" <peter@xxxxxxxxxx>
  • To: <duxhelp@xxxxxxxxxxxxx>
  • Date: Wed, 17 May 2006 14:27:18 -0400

Lissa,

OK.  Was Bart in low-density or high-density graphics?

- Peter 

-----Original Message-----
From: duxhelp-bounce@xxxxxxxxxxxxx [mailto:duxhelp-bounce@xxxxxxxxxxxxx] On
Behalf Of Melissa Hirshson
Sent: Wednesday, May 17, 2006 1:39 PM
To: duxhelp@xxxxxxxxxxxxx
Subject: [duxhelp] Re: another graphics issue

Peter,

This is what happened.

1) I turned on the machine cold, and ran the Bart graphic. The graphic image
embossed properly, but the page number in the upper right hand corner was
squished, (embossed in high-density mode).

2) After that, I ran a configuration listing, without having shut off the
machine, and it too ran in high density mode, and was therefore unreadable.

3) I shut off the machine and turned it back on again, and then ran the
listing again. It ran in normal, low-density mode.

Lissa

Peter Sullivan wrote:
> Lissa,
> 
> OK.
> 
> But the issue here isn't one of mixing two graphics modes, is it?  I 
> thought that the issue was mixing a text mode with graphics mode.  Is 
> that not working either?
> 
> - Peter
> 
> -----Original Message-----
> From: duxhelp-bounce@xxxxxxxxxxxxx 
> [mailto:duxhelp-bounce@xxxxxxxxxxxxx] On Behalf Of Melissa Hirshson
> Sent: Wednesday, May 17, 2006 12:18 PM
> To: duxhelp@xxxxxxxxxxxxx
> Subject: [duxhelp] Re: another graphics issue
> 
> Peter,
> 
> Yes. It looks like it embosses a page either in high density mode or 
> low density mode, but can't do some of each.
> 
> Lissa
> 
> Peter Sullivan wrote:
> 
>>Lissa,
>>
>>In a message after this one, you mentioned that the diagnostics page 
>>was printed as graphics, because that mode was "left over" from 
>>embossing a graphics image previously.
>>
>>Perhaps the same thing is going on here.
>>
>>Do you get a "squished" page number embossed when you emboss Bart 
>>after a fresh power-up?
>>
>>- Peter
>>
>>-----Original Message-----
>>From: duxhelp-bounce@xxxxxxxxxxxxx
>>[mailto:duxhelp-bounce@xxxxxxxxxxxxx] On Behalf Of Melissa Hirshson
>>Sent: Monday, May 08, 2006 3:09 PM
>>To: duxhelp@xxxxxxxxxxxxx
>>Subject: [duxhelp] another graphics issue
>>
>>When I embossed the Bart graphic on my Express 150, it also embossed 
>>the page number at the upper right hand corner in "high density" mode, 
>>which means that it came out looking squished.
>>
>>I will run your test shortly and report the results.
>>
>>Lissa

* * *
* This message is via list duxhelp at freelists.org.
* To unsubscribe, send a blank message with
*   unsubscribe
* as the subject to <duxhelp-request@xxxxxxxxxxxxx>. You may also
* subscribe, unsubscribe, and set vacation mode and other subscription
* options by visiting http://www.freelists.org.  The list archive
* is also located there.
* Duxbury Systems' web site is http://www.duxburysystems.com
* * *


* * *
* This message is via list duxhelp at freelists.org.
* To unsubscribe, send a blank message with
*   unsubscribe
* as the subject to <duxhelp-request@xxxxxxxxxxxxx>. You may also
* subscribe, unsubscribe, and set vacation mode and other subscription
* options by visiting http://www.freelists.org.  The list archive
* is also located there.
* Duxbury Systems' web site is http://www.duxburysystems.com
* * *

Other related posts: