[ddots-l] Re: sound card assignment for Jaws

Hello,

This information is at the following page;

http://www.dancingdots.com/main/ctfaq.htm#JFW

. Q: Is it possible to run JFW through my soundcard on my computer while 
running my music through my external sound card?
A: You should use your low-end sound card which may be built onto the PC's 
mother board, to produce JAWS speech. You can use your Delta card or other 
high-end
soundcard to play audio from Cakewalk SONAR. You can tell Windows to use the 
low-end card as the preferred audio device and you can make sure that Cakewalk
does not know about the low-end card but only about the Delta card. From now on 
in this little tutorial, "Delta card" will stand for any high-end soundcard.


Use the following strategy under Windows XP. If you're using a different 
version of Windows, this strategy should work but the exact steps may be 
somewhat
different. 

Telling Windows about your Low-end Card
list of 12 items nesting level 1
. Press the Windows Key to go to the Start Menu. 
. Press S until you hear Settings. 
. Press c for Control Panel or just press ENTER. 
. Press the letter S until you hear Sounds and Multimedia. 
. Press ENTER. 
. Press CONTROL+TAB until you reach the Audio tab. 
. Make sure that your low-end soundcard is selected as the preferred play back 
and recording device. 
. You probably also want to choose your low-end card for MIDI play back too, at 
least for now. 
. Tab to "Use only preferred devices" and be sure that it is checked. 
. Tab to the Apply button and press ENTER. 
. Tab to the OK button and press ENTER. At this point, Windows is set properly. 
. Reboot your PC. 
list end nesting level 1
Setting Cakewalk SONAR to Know about Your High-end Card
list of 7 items nesting level 1
. Run SONAR. 
. Press ALT+O, then the letter o to set Audio options. You'll probably come 
right up into the "General Tab" dialog but, if not, press CONTROL+TAB until
you're there. 
. Make sure your Delta card drivers are selected for both the Playback Timing 
Master and the Record Timing Master. 
. Press CONTROL+TAB to move to the Drivers page. Again, make sure that your 
Delta drivers are checked for input and output. In this dialog you will use
the space bar to check only those drivers which you want SONAR to use. You 
should check all Delta drivers shown for input and output and make sure that
the drivers listed for your low-end soundcard are not checked. 
. If you see an option to allow you to use the ASIO drivers under the Advanced 
tab, you should definitely check it. 
. Find the OK button in any of the Audio pages and press the space bar to 
select it. SONAR may tell you that the changes you have made will not take 
effect
until the next time you start SONAR. Press ENTER and close SONAR with ALT+F4. 
Re-boot your system. Restart SONAR and try playing the SONAR Audio and MIDI
DEMO2.cwb file (see below). 
. Note: with certain soundcards, you will need to unload and restart JAWS on 
booting up your system. Otherwise, you may hear JAWS speech coming through
your high-end soundcard despite setting up your Windows audio options properly 
in the Windows Control Panel as shown above. This un-loading and reloading
may even be necessary on systems that have had the jaws.ini file revised to 
list the low-end soundcard as synthesizer 1. 
list end nesting level 1
Do you have some speakers connected to your Delta card? If not, you can try 
using a pair of headphones. You must have some way of listening to the audio
signal from the Delta output. If you do, try opening the SONAR Audio and MIDI 
DEMO2.cwb file which you will find in the SONAR Sample Content folder. All
of the instruments in this project file are recorded on audio tracks which you 
should hear through your Delta card once you have followed the instructions
above. Only Track 4 is assigned to MIDI percussion which you should hear 
through the low-end soundcard's MIDI output unless your low-end card has no MIDI
output facility. If you don't hear that wood block ad other percussion on Track 
4, you'll need to set your MIDI options with ALT+O and the letter M. But
don't worry about that until you've corrected your audio set up. 

BTW, you will find excellent information on setting up your MIDI and audio 
hardware in Lessons 46-54 of the main CakeTalking tutorial. From your Windows
desktop (WINDOWS_KEY+M) type the letter C until you hear CakeTalking... Press 
ENTER. Type T until you hear "Tutorials" and press ENTER. Type C until you
hear: "CakeTalking Tutorial For Sonar 4.doc". Review the Table of Contents for 
the Lesson you wish to read. Ideally, you should eventually read this tutorial
document in its entirety.

Other related posts: