Interesting, I've read through all the docs to find it and nothing is mentioned about a Numeric Entry feature from the Pads on the X. I think I read the manual about five times not finding it. I know I found it on the "G" board though. Was it a ROM update? On 10/8/09, Mark Dew <jmkeybd1@xxxxxxxxxxx> wrote: > > Vince, the fantom x does that. > > Mark > > At 02:48 PM 10/8/2009 -0400, you wrote: >>Has anyone tried the Fantom "G" series yet? That has a feature which >>turns the Pad buttons into numeric keys for direct entry access with >>just a push of the "Numeric" button. >> >>On 10/8/09, Omar Binno <omarbinno@xxxxxxxxx> wrote: >>> wow. Thanks Mark. I had a fantom x a few years back, and I didn't > experiment >>> with it that far. I did notice that the left and right arrows wrapped >>> around. This is good to know though. >>> ----- Original Message ----- >>> From: Mark Dew >>> To: ddots-l@xxxxxxxxxxxxx >>> Sent: Thursday, October 08, 2009 1:43 PM >>> Subject: [ddots-l] Re: questions to fantom synthesizer >>> >>> >>> That is not the case with the fantom x. >>> I have edited all my favorite voices with out that experience. >>> The curssor up and down buttons stop at the top and botton. >>> There are some cases where the left and right will circle around. >>> It could very well be, I've been using Roland for 23 years and I am >>> used >>> to >>> the madness of it all. >>> After editing the voices I save them to the user section. >>> Then I put them in the favorite list. >>> There are 20 banks containing 16 slots to a bank where you can save a >>> voice. >>> When you bring up the favorite list the up and down cursor buttons > scrolls >>> through the banks and the f1 through f8 below the screen selects the >>> voice. >>> Hold the shift and press f1 through f8, >>> this selects the 9 through 16 voice of that bank. >>> Run the up button up and it stops at bank 1. >>> Run the down button down and it stops at bank 20. >>> They do not wrap around. >>> When you enter the edit mode, the f1 and f2 below the screen scrolls > throu >>> the different parameter pages. >>> F1 stops at page 1 and f2 stops at page 18. >>> The up and down cursor buttons selects the parameter to be edited. >>> They do not wrap. >>> I'm not sure, but there could be a setting some where in a menu that > would >>> change this. >>> Of course as you know as a blind user, we all have to be determined to >>> find >>> a way. >>> >>> Cheers! >>> >>> Mark >>> >>> >>> >>> >>> >>> At 11:43 AM 10/8/2009 -0400, you wrote: >>> > Most Roland keyboards are largely inaccessible for blind users. >>> The >>> >reason for that is that their cursors wrap around in the menus. They >>> don't >>> >stop at the top or the bottom. So you won't know where you left off >>> if >>> you >>> >forget your last position on a menu. They do sound great though. >>> ----- >>> >Original Message ----- From: Oliver Zenz To: >>> ddots-l@xxxxxxxxxxxxx >>> > Sent: Thursday, October 08, 2009 11:26 AM Subject: [ddots-l] >>> >questions to fantom synthesizer >>> >Hi Listers, >>> > >>> >some times I have heared, that the roland fantom gear is little or >>> more >>> >accessible by blind users. does anny body of you know something >>> more? >>> > >>> >I heared the Juno G, and this little thing sounds pretty well! so I >>> found >>> >out, that it consists to be of the same soundchip as like the >>> fantom, >>> >but it >>> >just has 61 keys, and i was looking after one with 88 keys. But all >>> models >>> >have different sounds, and i would love to have the same sounds in >>> anny >>> >keyboard of this gear, so under the link below you will find a > kind of >>> >editor and librourian that lets you transfer sounds from one to the >>> other, >>> >wich is normally not possible, because roland placed the waves for > the >>> >sounds in each model in different places. now this editor knows >>> where >>> the >>> >waves of each model are placed and makes the apropriat changes to >>> the >>> >sounds. so now one can transfer a sound from the fantom-xs to the > juno >>> g >>> >and >>> >so on. >>> > >>> >http://perplextor.wordpress.com/category/juno-g/ >>> > >>> >Thanks and enjoy. >>> > >>> >ciao, >>> > >>> >Oliver >>> > >>> >PLEASE READ THIS FOOTER AT LEAST ONCE! >>> >To leave the list, click on the immediately following link: >>> >ddots-l-request@xxxxxxxxxxxxx?subject=unsubscribe >>> >If this link doesn't work then send a message to: >>> >ddots-l-request@xxxxxxxxxxxxx >>> >and in the Subject line type >>> >unsubscribe >>> >For other list commands such as vacation mode, >>> >click on the immediately following link: >>> >ddots-l-request@xxxxxxxxxxxxx?subject=faq or >>> >send a message, to >>> >ddots-l-request@xxxxxxxxxxxxx >>> >and in the Subject line type >>> >faq >>> > >>> > >>> PLEASE READ THIS FOOTER AT LEAST ONCE! >>> To leave the list, click on the immediately following link: >>> ddots-l-request@xxxxxxxxxxxxx?subject=unsubscribe >>> If this link doesn't work then send a message to: >>> ddots-l-request@xxxxxxxxxxxxx >>> and in the Subject line type >>> unsubscribe >>> For other list commands such as vacation mode, >>> click on the immediately following link: >>> ddots-l-request@xxxxxxxxxxxxx?subject=faq or >>> send a message, to >>> ddots-l-request@xxxxxxxxxxxxx >>> and in the Subject line type >>> faq >>> >> >> >>-- >>Vince Mistretta >>Call me at 561-234-7631 >>Skype Name: vin5451 (Please email me first) >>PLEASE READ THIS FOOTER AT LEAST ONCE! >>To leave the list, click on the immediately following link: >>ddots-l-request@xxxxxxxxxxxxx?subject=unsubscribe >>If this link doesn't work then send a message to: >>ddots-l-request@xxxxxxxxxxxxx >>and in the Subject line type >>unsubscribe >>For other list commands such as vacation mode, >>click on the immediately following link: >>ddots-l-request@xxxxxxxxxxxxx?subject=faq or >>send a message, to >>ddots-l-request@xxxxxxxxxxxxx >>and in the Subject line type >>faq >> >> > PLEASE READ THIS FOOTER AT LEAST ONCE! > To leave the list, click on the immediately following link: > ddots-l-request@xxxxxxxxxxxxx?subject=unsubscribe > If this link doesn't work then send a message to: > ddots-l-request@xxxxxxxxxxxxx > and in the Subject line type > unsubscribe > For other list commands such as vacation mode, > click on the immediately following link: > ddots-l-request@xxxxxxxxxxxxx?subject=faq or > send a message, to > ddots-l-request@xxxxxxxxxxxxx > and in the Subject line type > faq > > -- Vince Mistretta Call me at 561-234-7631 Skype Name: vin5451 (Please email me first) PLEASE READ THIS FOOTER AT LEAST ONCE! To leave the list, click on the immediately following link: ddots-l-request@xxxxxxxxxxxxx?subject=unsubscribe If this link doesn't work then send a message to: ddots-l-request@xxxxxxxxxxxxx and in the Subject line type unsubscribe For other list commands such as vacation mode, click on the immediately following link: ddots-l-request@xxxxxxxxxxxxx?subject=faq or send a message, to ddots-l-request@xxxxxxxxxxxxx and in the Subject line type faq