[ddots-l] Re: Help needed with M-Audio Delta 1010LT Mixer

Hey Jason, I've found that with the scripts, the second fader group doesn't
seem to work, for example, when trying to raise the volume of the inputs 3
and 4 I had to click the right scroll arrow till the mixer scrolled to the
end of the screen, and then go to the top and use the jaws cursor/mouse to
hit the scroll up symbol which would raise the volumes for inputs 3 and 4.
I could not seem to do that with just the keyboard, and even after doing
that, i went through all the sliders to see if I could find the slider with
the different settings, as they were all at 0 percent except the 3 and 4,
and I was unable to find them, I think I only got the sliders for the wave
outputs, thats it.  Maybe this is why you aren't getting luck?  I'm thinking
that since the new version of the drivers (last year I believe) the control
panel was modified, so the scripts are having a bit of a problem.  Try using
the mouse, scrolling all the way to the right by pressing the right scroll
arrow at the bottom of the screen quite a few times, then on the top of the
screen you'll see header bars with inputs 1, 2, 3, 4, etc.  then press down
arrow, you'll see the volume portion, then the pan portion should follow,
try editing the pan with the mouse, not forgetting to go over to the third
and fourth scroll symbols, as the first 2 are for the inputs 1 and 2...

HTH, D!J!X!


-----Original Message-----
From: ddots-l-bounce@xxxxxxxxxxxxx [mailto:ddots-l-bounce@xxxxxxxxxxxxx] On
Behalf Of Jayson Smith
Sent: Tuesday, November 27, 2007 8:35 AM
To: ddots-l@xxxxxxxxxxxxx
Subject: [ddots-l] Help needed with M-Audio Delta 1010LT Mixer

Hi,

     I need some help with the mixer on the Delta 1010LT. I'm in the middle
of a recording job which I need to get done as soon as possible. I have my
main mixer hooked up to hardware in 3 and 4. Somehow, the pan on those
inputs has been messed up, and both channels are coming through the left
channel. Output is panned properly, and that input is also recorded wrong,
so I know that's the problem. The problem is, I can't figure out how to
change it. I can successfully navigate to the second fader group, but all
the pans look correct, and checking all the Mute boxes, I can only mute one
channel of that input, not both. I've never quite understood how the input
section of the monitor mixer tab works. I  have some old scripts which I
recompiled for Jaws 7.0, but I'm wondering if there are any newer scripts? I
don't have anyone sighted coming over until Friday, and really need to get
this done before then. Any help with this problem would be greatly
appreciated. Thanks.
Jayson
** To leave the list, click on the immediately-following link:-
** [mailto:ddots-l-request@xxxxxxxxxxxxx?subject=unsubscribe]
** If this link doesn't work then send a message to:
** ddots-l-request@xxxxxxxxxxxxx
** and in the Subject line type
** unsubscribe
** For other list commands such as vacation mode, click on the
** immediately-following link:-
** [mailto:ddots-l-request@xxxxxxxxxxxxx?subject=faq]
** or send a message, to
** ddots-l-request@xxxxxxxxxxxxx with the Subject:- faq




** To leave the list, click on the immediately-following link:-
** [mailto:ddots-l-request@xxxxxxxxxxxxx?subject=unsubscribe]
** If this link doesn't work then send a message to:
** ddots-l-request@xxxxxxxxxxxxx
** and in the Subject line type
** unsubscribe
** For other list commands such as vacation mode, click on the
** immediately-following link:-
** [mailto:ddots-l-request@xxxxxxxxxxxxx?subject=faq]
** or send a message, to 
** ddots-l-request@xxxxxxxxxxxxx with the Subject:- faq

Other related posts: