[bksvol-discuss] Re: opticbook and Kurzweil version 12

I would also add to do an actual check of your scanner and recognition settings and see if you can tell where you're having problems--on the inner or outer ends of lines, perhaps? Maybe it's the particular book?
----- Original Message ----- From: "robert tweedy" <roberttweedy@xxxxxxx> 
To: <bksvol-discuss@xxxxxxxxxxxxx>
Sent: Saturday, December 05, 2009 7:40 AM
Subject: [bksvol-discuss] Re: opticbook and Kurzweil version 12
We have three going about the same time and no problems with them. Use the weigh driver. ----- Original Message ----- From: "Julia" <julia.kulak@xxxxxxxxxxxx> 
To: <bksvol-discuss@xxxxxxxxxxxxx>
Sent: Friday, December 04, 2009 9:03 PM
Subject: [bksvol-discuss] Re: opticbook and Kurzweil version 12



Oo, you have two scanners at your disposal, how exciting!
Let me know what you find.
Thanks for your help.
Julia
----- Original Message ----- From: "Shelley L. Rhodes" <guidinggolden@xxxxxxxxx> 
To: <bksvol-discuss@xxxxxxxxxxxxx>
Sent: Friday, December 04, 2009 9:44 PM
Subject: [bksvol-discuss] Re: opticbook and Kurzweil version 12
I haven't had problems with my Epson 1660 but haven't connected up the Optibook, that was tomorrow's adventure, smile. 

But my scans with the Epson are better.


Shelley L. Rhodes, VRT

Guide dogs for the Blind Alumni Association
www.guidedogs.com
Reading a book is like rewriting it for yourself. You bring to a novel, anything you read, all your experience of the world. You bring your history and you read it in your own terms. -Angela Carter, novelist and journalist (1940-1992)
----- Original Message ----- From: "Mystery Train" <captinlogic@xxxxxxxxx> 
To: <bksvol-discuss@xxxxxxxxxxxxx>
Sent: Friday, December 04, 2009 6:36 PM
Subject: [bksvol-discuss] Re: opticbook and Kurzweil version 12
Maybe you have to readjust your scanning area, I don't know, don't scan with k1000. ----- Original Message ----- From: "Julia" <julia.kulak@xxxxxxxxxxxx> 
To: <bksvol-discuss@xxxxxxxxxxxxx>
Sent: Friday, December 04, 2009 3:22 PM
Subject: [bksvol-discuss] opticbook and Kurzweil version 12



Hi everyone, I'm back.
I'm trying out the demo of Kurzweil version 12 with my opticbook, and it seems to be getting worse results then with version 11. Even on hardbacks there are errors. Am I alone in my predicament? Is there some special setting I need to tweak to make it work better? Is it true what I've heard, that version 12 is a significant improvement over 11, because from where I sit it seems like its quite a bit worse. Maybe my scanner is dying, I don't know. Although considering that I got it replaced six months ago I doubt that is the case. Somehow it seemed to be scanning much better before the replace. 
Can someone please shed some light on this puzzling matter.
Thanks in advance for your help.
Julia
Julia
To unsubscribe from this list send a blank Email to
bksvol-discuss-request@xxxxxxxxxxxxx
put the word 'unsubscribe' by itself in the subject line. To get a list of available commands, put the word 'help' by itself in the subject line. 



To unsubscribe from this list send a blank Email to
bksvol-discuss-request@xxxxxxxxxxxxx
put the word 'unsubscribe' by itself in the subject line. To get a list of available commands, put the word 'help' by itself in the subject line. 



To unsubscribe from this list send a blank Email to
bksvol-discuss-request@xxxxxxxxxxxxx
put the word 'unsubscribe' by itself in the subject line. To get a list of available commands, put the word 'help' by itself in the subject line. 




To unsubscribe from this list send a blank Email to
bksvol-discuss-request@xxxxxxxxxxxxx
put the word 'unsubscribe' by itself in the subject line. To get a list of available commands, put the word 'help' by itself in the subject line. 




To unsubscribe from this list send a blank Email to
bksvol-discuss-request@xxxxxxxxxxxxx
put the word 'unsubscribe' by itself in the subject line. To get a list of available commands, put the word 'help' by itself in the subject line. 



To unsubscribe from this list send a blank Email to
bksvol-discuss-request@xxxxxxxxxxxxx
put the word 'unsubscribe' by itself in the subject line.  To get a list of 
available commands, put the word 'help' by itself in the subject line.

Other related posts: