That's good stuff, thank you Aaron. Tom -----Original Message----- From: amayausers-bounce@xxxxxxxxxxxxx [mailto:amayausers-bounce@xxxxxxxxxxxxx] On Behalf Of Linen Barn Sent: Friday, September 22, 2006 4:21 PM To: amayausers@xxxxxxxxxxxxx Subject: [amayausers] Re: THREAD THROWING OFF TO THE LEFT Just inside the hub and it just takes a little. You do not want the grease to get on the yellow surface or the red surface as it will cause the thread to slip off to the side. Both the Red and Yellow rollers need to be removed and greased every month or 2. If you start to see a fine red dust in the roller area its cause the grease is gone and the plastic is wearing off. At the sign of this red dust you should grease both rollers and once again be careful not to use to much or to get any on the actual roller surface where the thread goes cause it will cause problems :) Aaron Sargent The Linen Barn linen@xxxxxxxxxxx 541-770-2957 Medford, OR ----- Original Message ----- From: "Tom Ladow" <tcladow@xxxxxxxxxxxxxxxxxxxxxxxxxx> To: <amayausers@xxxxxxxxxxxxx> Sent: Friday, September 22, 2006 12:09 PM Subject: [amayausers] Re: THREAD THROWING OFF TO THE LEFT > John; > When you say grease the black hub, are you talking inside the hub, > outside > the hub or both? > > > Thanks, > > Tom > -----Original Message----- > From: amayausers-bounce@xxxxxxxxxxxxx > [mailto:amayausers-bounce@xxxxxxxxxxxxx] On Behalf Of John Yaglenski > Sent: Friday, September 22, 2006 2:38 PM > To: amayausers@xxxxxxxxxxxxx > Subject: [amayausers] Re: THREAD THROWING OFF TO THE LEFT > > Take out the thread feed roller and pinch rollers. Get some lightly soapy > water - and clean them off including any remnant grease. Repeat if > necessary till all the grime is off. Then rinse with water very well. > Dry > with a soft cloth. Then regrease both items appropriately and put them > back > on the machine. > > Should work. If it doesn't - replace one or both. > > John > > -----Original Message----- > From: amayausers-bounce@xxxxxxxxxxxxx > [mailto:amayausers-bounce@xxxxxxxxxxxxx] On Behalf Of Tom Ladow > Sent: Friday, September 22, 2006 8:47 AM > To: amayausers@xxxxxxxxxxxxx > Subject: [amayausers] THREAD THROWING OFF TO THE LEFT > > > I have experienced the thread being thrown off to the left (as you look > at > the roller)on one of my red feed rollers. This is new kink for me but has > virtually rendered this needle position useless. Any ideas on how to fix > this problem, I sure would appreciate it. > > Tom L. > Indiana > > > > =========================================================== > > The AmayaUsers Mailing List > Website: http://www.amayausers.com > Discussion Board: http://www.amayausers.com/boards > Subscribe/Unsubscribe: http://www.amayausers.com/list > > =========================================================== > > =========================================================== > > The AmayaUsers Mailing List > Website: http://www.amayausers.com > Discussion Board: http://www.amayausers.com/boards > Subscribe/Unsubscribe: http://www.amayausers.com/list > > =========================================================== > > > =========================================================== > > The AmayaUsers Mailing List > Website: http://www.amayausers.com > Discussion Board: http://www.amayausers.com/boards > Subscribe/Unsubscribe: http://www.amayausers.com/list > > =========================================================== =========================================================== The AmayaUsers Mailing List Website: http://www.amayausers.com Discussion Board: http://www.amayausers.com/boards Subscribe/Unsubscribe: http://www.amayausers.com/list =========================================================== =========================================================== The AmayaUsers Mailing List Website: http://www.amayausers.com Discussion Board: http://www.amayausers.com/boards Subscribe/Unsubscribe: http://www.amayausers.com/list ===========================================================