[amayausers] Re: Nylon and Pulling

Sharon,

I don't have the original, I immediately enlarged it.  It is a Dakota file
original size was 5.57 x 2.41 and had 14,856 stitches.

We are using Poly thread at 1100 speed.

I need to do this design on fleece as well.  I will test that after supper.

I appreciate all your help.

Lisa & Don Ridley
Wolf Embroidery
Wolfemb@xxxxxxxx
----- Original Message -----
From: "Sharon" <springer37@xxxxxxxxxxxx>
To: <amayausers@xxxxxxxxxxxxx>
Sent: Thursday, December 30, 2004 2:59 PM
Subject: [amayausers] Re: Nylon and Pulling


> Lisa,
> Send me the original file as well as the enlarged saved file you are
trying
> to stitch out and I will see what I can do for you. It appears to just be
a
> density, pull comp problem created by over enlargement of the design in
> combination with the type of fabric.
>
> Sharon failed to ask what speed(s) you are sewing this design at..poly
> thread, rayon thread??
> Rod
>
> Rod Springer
> Melco Trained Technician/Owner
> (Design Shop Pro+ Digitizing)
> Boise, ID
> (208) 938-3038
> springer37@xxxxxxxxxxxx
> ----- Original Message -----
> From: "Wolf Embroidery" <Wolfemb@xxxxxxxx>
> To: <amayausers@xxxxxxxxxxxxx>
> Sent: Thursday, December 30, 2004 12:10 PM
> Subject: [amayausers] Re: Nylon and Pulling
>
>
> > This one was much better but still problems.
> > The lower part of the L did not fill.  There is some of the fill showing
> > outside the outline on the right lower part of the L as well as The
right
> > lower part of the I.
> >
> >
> > Lisa & Don Ridley
> > Wolf Embroidery
> > Wolfemb@xxxxxxxx
> > ----- Original Message -----
> > From: "Sharon" <springer37@xxxxxxxxxxxx>
> > To: <amayausers@xxxxxxxxxxxxx>
> > Sent: Thursday, December 30, 2004 1:37 PM
> > Subject: [amayausers] Re: Nylon and Pulling
> >
> >
> > > Send it to us Lisa and we will take a look.  How soon are you needing
> this
> > > to be done?
> > > Rod Springer
> > > Melco Trained Technician/Owner
> > > (Design Shop Pro+ Digitizing)
> > > Boise, ID
> > > (208) 938-3038
> > > springer37@xxxxxxxxxxxx
> > > ----- Original Message -----
> > > From: "Wolf Embroidery" <Wolfemb@xxxxxxxx>
> > > To: <amayausers@xxxxxxxxxxxxx>
> > > Sent: Thursday, December 30, 2004 11:08 AM
> > > Subject: [amayausers] Re: Nylon and Pulling
> > >
> > >
> > > > I have poly mesh that I can use because the lining is white.  Should
I
> > use
> > > > that with regular backing or alone?
> > > >
> > > > I increased the Pull comp from 100-110% this is all that I could
> > increase.
> > > > I enlarged the design way more than recommended, but it seemed to
> stitch
> > > > well on the sample.
> > > >
> > > > Is Rod able to look at the design?  I'm willing to pay, my digitizer
> is
> > on
> > > > vacation.
> > > >
> > > > Lisa & Don Ridley
> > > > Wolf Embroidery
> > > > Wolfemb@xxxxxxxx
> > > > ----- Original Message -----
> > > > From: "Sharon" <springer37@xxxxxxxxxxxx>
> > > > To: <amayausers@xxxxxxxxxxxxx>
> > > > Sent: Thursday, December 30, 2004 12:44 PM
> > > > Subject: [amayausers] Re: Nylon and Pulling
> > > >
> > > >
> > > > > Depending on the color of the nylon jackets and the weight of the
> > > lining,
> > > > > Lisa, I would use a poly-mesh cutaway if the nylon is
> > white--otherwise,
> > > a
> > > > > medium weight cutaway if the design is pretty dense.  I like to
use
> a
> > > > weight
> > > > > that is similar to the weight of my garment but if the design is
> > pretty
> > > > > "heavy" then I use a heavier cutaway.  Hooping needs to be tight
but
> > > don't
> > > > > stretch your fabric.  At times I have used strips of rubber shelf
> > lining
> > > > > inside my hoop to help anchor the fabric if it tends to slip. If
you
> > > > > enlarged the design, how much larger did you enlarge it?  You may
> need
> > > to
> > > > > add density and pull comp both.  I would probably start with
adding
> > 20%
> > > > pull
> > > > > comp and try it on a scrap of nylon to test it.  I have to run to
my
> > > other
> > > > > job for a bit but Rod is here and can tell you where to find those
> > > > settings
> > > > > if you need help.
> > > > > Sharon
> > > > > Rod Springer
> > > > > Melco Trained Technician/Owner
> > > > > (Design Shop Pro+ Digitizing)
> > > > > Boise, ID
> > > > > (208) 938-3038
> > > > > springer37@xxxxxxxxxxxx
> > > > > ----- Original Message -----
> > > > > From: "Wolf Embroidery" <Wolfemb@xxxxxxxx>
> > > > > To: <amayausers@xxxxxxxxxxxxx>
> > > > > Sent: Thursday, December 30, 2004 10:21 AM
> > > > > Subject: [amayausers] Re: Nylon and Pulling
> > > > >
> > > > >
> > > > > > Cut Away Stabilizer.  Very tight hooping.  8" X 3.5"  Stock
design
> > > that
> > > > I
> > > > > > enlarged.(Probably too much.)  No pull comp on my end.  I'm not
a
> > > > > digitizer
> > > > > > and know very little about the process.
> > > > > >
> > > > > > Lisa & Don Ridley
> > > > > > Wolf Embroidery
> > > > > > Wolfemb@xxxxxxxx
> > > > > > ----- Original Message -----
> > > > > > From: "Sharon" <springer37@xxxxxxxxxxxx>
> > > > > > To: <amayausers@xxxxxxxxxxxxx>
> > > > > > Sent: Thursday, December 30, 2004 11:47 AM
> > > > > > Subject: [amayausers] Re: Nylon and Pulling
> > > > > >
> > > > > >
> > > > > > > Hi Lisa,
> > > > > > > What stabilizer are you using? How tight are you hooping?  How
> > large
> > > > is
> > > > > > the
> > > > > > > design?  Is the design digitized by someone or a commercial
> > design?
> > > > > Have
> > > > > > > you put any pull comp in?
> > > > > > > Sharon
> > > > > > >
> > > > > > > Rod Springer
> > > > > > > Melco Trained Technician/Owner
> > > > > > > (Design Shop Pro+ Digitizing)
> > > > > > > Boise, ID
> > > > > > > (208) 938-3038
> > > > > > > springer37@xxxxxxxxxxxx
> > > > > > > ----- Original Message -----
> > > > > > > From: "Wolf Embroidery" <Wolfemb@xxxxxxxx>
> > > > > > > To: <amayausers@xxxxxxxxxxxxx>
> > > > > > > Sent: Thursday, December 30, 2004 9:21 AM
> > > > > > > Subject: [amayausers] Re: Nylon and Pulling
> > > > > > >
> > > > > > >
> > > > > > > > I'm stitching out Cheerleader jackets made of Polyester
shell
> > and
> > > a
> > > > > thin
> > > > > > > > cotton liner.  The design stitched perfectly on backing but
> when
> > I
> > > > > > > stitched
> > > > > > > > on the jacket it pulled.  Put a pucker in the jacket and did
> not
> > > > > outline
> > > > > > > > properly.  Material thickness is set at 4
> > > > > > > >
> > > > > > > > Any Suggestions?
> > > > > > > >
> > > > > > > > Lisa & Don Ridley
> > > > > > > > Wolf Embroidery
> > > > > > > > Wolfemb@xxxxxxxx
> > > > > > > >
> > > > > > > >
> > > > > > >
> > > > > > >
> > > > > > >
> > > > > >
> > > > > >
> > > > >
> > > > >
> > > > >
> > > >
> > > >
> > >
> > >
> > >
> >
> >
> > -- Binary/unsupported file stripped by Ecartis --
> > -- Type: application/octet-stream
> > -- File: Lions.ofm
> >
> >
> >
>
>
>

Other related posts: