[amayausers] Re: Fastframes, and bobbin cover ?

The plastic cover that you are refering to can be removed BUT it must be 
installed when using the cap driver. This plastic cover is the holder/guide 
for the main shaft of the cap driver. I have yet to see a need to remove 
this cover for sewing any garment.

The foward screw in this cover is an extremly close fit inside the shaft 
hole. On a tech call, we had a new Amaya that the client was unable to 
install the cap driver. We discovered 2 washers had been placed on this 
forward screw that allowed the head of the screw to protrude down into the 
shaft hole by about a 1/32 of an inch. this would then not allow the cap 
driver shaft to pass by it.

Rod Springer

Embroidery Cottage
Rod & Sharon Springer
Melco Amaya Tech & Trainer
Design Shop Pro+ Digitizing

Boise, ID  83713
208-938-3038
----- Original Message ----- 
From: <DLCompton@xxxxxxx>
To: <amayausers@xxxxxxxxxxxxx>
Sent: Wednesday, May 24, 2006 11:10 AM
Subject: [amayausers] Re: Fastframes, and bobbin cover ?


>
> I don't know about that one. I've never even tried (nor obviously have
> needed to). Jeff? Rod?
>
> Dorothy
>
>
> In a message dated 5/23/2006 10:13:44 PM Pacific Daylight Time,
> irisembroidery@xxxxxxxxxxxxx writes:
> How  about the one which slides in the cap frame?  Did you know if I  can
> remove that?  The screws seem to be different.
>
> Best  Regards,
> Veena Viswanath
>
>
> Iris  Embroidery
> www.IrisEmbroidery.com
> (510)-226-6171
>
> -----Original  Message-----
> From:  amayausers-bounce@xxxxxxxxxxxxx
> [mailto:amayausers-bounce@xxxxxxxxxxxxx] On  Behalf Of DLCompton@xxxxxxx
> Sent: Tuesday, May 23, 2006 9:30 PM
> To:  amayausers@xxxxxxxxxxxxx
> Subject: [amayausers] Re: Fastframes, and bobbin  cover ?
>
>
> I've had to remove the bottom of the bobbin case for an  apron pocket 
> order
> (and tote pocket order) without any problem. I  was really careful in 
> putting
>
> everything back  together.
>
>
> Dorothy  Compton
> Bee  Embroidered
> _www.BeeEmbroidered.com_ (http://www.beeembroidered.com/)
> (916)  635-7467
> Rancho Cordova, CA
>
> In a message dated  5/23/2006 6:40:07 PM Pacific Daylight Time,
> irisembroidery@xxxxxxxxxxxxx writes:
>
> Hello  all,
> I recently  got fast frames since I wanted to do some embroidery  on  a
> glove.  I just hooked it up and wanted to know it it was  possible  to 
> remove
> the bottom part of the bobbin case and an other  piece on the  bottom of 
> the
> bobbin case (something used to hook up the  hat driver?)   If I removed
> either
> or both of them, would  there be any problem with my  machine afterwards?
>
> Thanks for the  information
>
>
> Best  Regards,
> Veena  Viswanath
>
>
> Iris   Embroidery
> www.IrisEmbroidery.com
> (510)-226-6171
>
>
>
>
>
>
>
> ===========================================================
>
> The AmayaUsers Mailing List
> Website: http://www.amayausers.com
> Discussion Board: http://www.amayausers.com/boards
> Subscribe/Unsubscribe: http://www.amayausers.com/list
>
> =========================================================== 

=========================================================== 

The AmayaUsers Mailing List
Website: http://www.amayausers.com
Discussion Board: http://www.amayausers.com/boards
Subscribe/Unsubscribe: http://www.amayausers.com/list

===========================================================

Other related posts: