[amayausers] Re: Amaya not centering properly

When I sew beanies I sometimes put my design right above the center orgin.
When I load the design into OS I notice the same thing, the design is a
little lower than I had it setup.  Its not off enough to mess me up so I
usually don't worry about it.

Aaron Sargent
The Linen Barn
linen@xxxxxxxxxxx
Medford, Oregon
----- Original Message -----
From: "Mark Middlekauff" <markm@xxxxxxxxxxxxxxxxxxxx>
To: <amayausers@xxxxxxxxxxxxxxxx>
Sent: Wednesday, February 25, 2004 5:25 AM
Subject: RE: [amayausers] Amaya not centering properly


> Just curious, What OS are you using? I know in older software the hoop
> limits were moved to account for the presser foot. I think they have been
> moved back to center. This is 5.07.023. I hope this helps some.
>
>
>
>         Mark Middlekauff
>      Production/IT Manager
>       Consumer Concepts
>     (252) 247-7000 ext. 207
>
>
>
> -----Original Message-----
> From: Paul Tilton [mailto:ptilton@xxxxxxxxx]
> Sent: Wednesday, February 25, 2004 3:39 AM
> To: amayausers@xxxxxxxxxxxxxxxx; Rod & Sharon
> Subject: Re: [amayausers] Amaya not centering properly
>
>
> I am NOT using the laser light to determine the center of the design. I
sew
> the design in the "center" according to the software (both Design Shop and
> Amaya OS). Before I remove from the hoop I can see it is not on center,
> check it with a protractor and ruler, it is off! Remove from hoop, take
> measurements using the crease formed from the hoop for a more accurate
> measurement, it is about 2MM off to the right and 2MM low. Bizarre....
>
> Rod & Sharon <springer37@xxxxxxxxxxxx> wrote:Paul,
> Question. Are you using the laser light to center the design in the hoop
> ?
>
> I recently went to tech training in Denver and boy, did I learn a lot of
> really interesting stuff about these machines.
>
> The laser light, if relied on to find absolute center in the design can
> cause a problem IF it is not in the proper adjustment. Even when it is
> adjusted properly for center on flat stitching, trying to use it to trace
a
> perfect stitch outline dosen't pan out either. This is especially true
when
> using the hat driver because of the curved surface. The laser light gets
you
> very close but can't be relied on it to be absolutely perfect...
>
>
>
>
> ----- Original Message -----
> From: "Paul Tilton"
>
> To:
> Sent: Tuesday, February 24, 2004 11:53 AM
> Subject: [amayausers] Amaya not centering properly
>
>
> > At first I thought is was an optical illusion, often my designs seemed
> to
> > be sewing a little bit right of center, so I did a test. I just created
> a
> > design, a simple circle outline, about the size of a quarter. I center
> it
> > using design shop, looks fine on the crosshairs, perfectly centered. I
> load
> > the design in Amaya OS, it looks a little low in the crosshairs, but
> > centering it doesn't change anything. I sew out the design, then get out
> my
> > ruler and protractor, sure enough the center of the design is about 3mm
> > right and 3mm low of center of the hoop...
> >
> > I can adjust the starting position of the hoop before I sew to correct
> the
> > problem, but any ideas on why this is happening?
> >
> > Thanks...
> >
> >
> >
> > Paul Tilton
> > Sandhills Stitches
> > Whispering Pines, NC
> >
> >
> > ---------------------------------------------------------------------
> > To unsubscribe, e-mail: amayausers-unsubscribe@xxxxxxxxxxxxxxxx
> > For additional commands, e-mail: amayausers-help@xxxxxxxxxxxxxxxx
> >
> >
>
>
> ---------------------------------------------------------------------
> To unsubscribe, e-mail: amayausers-unsubscribe@xxxxxxxxxxxxxxxx
> For additional commands, e-mail: amayausers-help@xxxxxxxxxxxxxxxx
>
>
>
> ---------------------------------
> Do you Yahoo!?
> Yahoo! Mail SpamGuard - Read only the mail you want.
>
>
> ---------------------------------------------------------------------
> To unsubscribe, e-mail: amayausers-unsubscribe@xxxxxxxxxxxxxxxx
> For additional commands, e-mail: amayausers-help@xxxxxxxxxxxxxxxx
>
>



---------------------------------------------------------------------
To unsubscribe, e-mail: amayausers-unsubscribe@xxxxxxxxxxxxxxxx
For additional commands, e-mail: amayausers-help@xxxxxxxxxxxxxxxx

Other related posts: