[amayausers] Re: Advice on settings for Hooptech system

Hi, Wendy and all-
Here are my current Hooptech settings for TCS1 and TCS2 windows. You may
need to adjust the angle of the clamping plate to get as close to the edges
as I have listed. If the clamping window goes too low, it may catch on your
Amaya needle plate and restrict movement. Please be careful when entering
the values: if you have any doubt on direction (+/-) of movement, make a
small adjustment first to confirm (1/4 inch or so). Also, keep the clamp
closed while adjusting. Finally, with the new Amaya OS, I found the Hoop
Manager did not respond the way I expected. I don't remember what I had to
do to make it work, but I believe I picking the correct hoop shape was a
critical step that had to be right the first time. You can always delete the
hoop definition if you get one messed up.

TCS2 - Window B1
x-dimension = 4.5"
y-dimension = 6.0"
X Hoop Offset = 0
Y Hoop Offset = -3.0 (NOTE: Negative value)
thickness = 0.252
default sew margin = 0.15 in.

TCS2 - Window B3
x-dimension = 7.5"
y-dimension = 6.0"
X Hoop Offset = 0
Y Hoop Offset = -3.0 (NOTE: Negative value)
thickness = 0.252
default sew margin = 0.15 in.


TCS1 - Window P1 (double check limits - I don't use this much)
x-dimension = 2.5"
y-dimension = 4.0"
X Hoop Offset = 0
Y Hoop Offset = -2.374 (NOTE: Negative value)
thickness = 0.252
default sew margin = 0.15 in.


TCS1 - Window P2
x-dimension = 3.5"
y-dimension = 4.0"
X Hoop Offset = 0
Y Hoop Offset = -2.374 (NOTE: Negative value)
thickness = 0.252
default sew margin = 0.15 in.

TCS1 - Window P3
x-dimension = 4.5"
y-dimension = 4.5"
X Hoop Offset = 0
Y Hoop Offset = -2.374 (NOTE: Negative value)
thickness = 0.252
default sew margin = 0.15 in.

Sincerely,

David O'Connor
O'Connor & Co. Custom Embroidery
Westerville, OH

----- Original Message ----- 
From: "wl solomonson" <wlsolomonson@xxxxxxxxxxx>
To: <amayausers@xxxxxxxxxxxxxxxx>
Sent: Friday, May 21, 2004 11:51 AM
Subject: Re: [amayausers] Advice on settings for Hooptech system


> David,
> I haven't installed my OS upgrade yet but would like your settings for it
so
> I'm ready to go when I get around to doing the install.
> Thanks,
> Wendy
> Itchin' To Stitch
> MN
>
>
> >From: "O'Connor & Co. Custom Embroidery" <oconnorco@xxxxxxxxxx>
> >Reply-To: amayausers@xxxxxxxxxxxxxxxx To: <amayausers@xxxxxxxxxxxxxxxx>
> >Subject: Re: [amayausers] Advice on settings for Hooptech system
> >Date: Thu, 20 May 2004 20:33:14 -0400
> >
> >Please let me know if you still need settings for the Hooptech and I'll
get
> >them posted here- I just did ours again after loading the OS upgrade, so
> >they are a bit different from before. Hope it is going well for you-
> >-david O.
> >----- Original Message -----
> >From: <Pupcakesemb@xxxxxxx>
> >To: <amayausers@xxxxxxxxxxxxxxxx>
> >Sent: Friday, May 14, 2004 5:26 PM
> >Subject: [amayausers] Advice on settings for Hooptech system
> >
> >
> > > I have purchased an EMS/Hooptech clamping system--the smaller
> >one---itCS1
> >and have the two cap sides, cap back, and a 4.5 inch square frames.  I
need
> >advice on the appropriate settings to input in the Amaya OS.
> > >
> > > I recall that another member of this list has this system installed.
I'm
> >hoping you will share your settings with me. (And,I hope to share this
with
> >Melco so they can add it to their frequently asked questions data base!)
> >Many thanks!
> > >
> > > Pati Segar
> > > Patricia Segar Designs (formerly Pupcakes Embroidery)
> > > pupcakesemb@xxxxxxx
> > >
> > >
> > > ---------------------------------------------------------------------
> > > To unsubscribe, e-mail: amayausers-unsubscribe@xxxxxxxxxxxxxxxx
> > > For additional commands, e-mail: amayausers-help@xxxxxxxxxxxxxxxx
> > >
> > >
> >
> >
> >
> >---------------------------------------------------------------------
> >To unsubscribe, e-mail: amayausers-unsubscribe@xxxxxxxxxxxxxxxx
> >For additional commands, e-mail: amayausers-help@xxxxxxxxxxxxxxxx
> >
>
> _________________________________________________________________
> Stop worrying about overloading your inbox - get MSN Hotmail Extra
Storage!
> http://join.msn.click-url.com/go/onm00200362ave/direct/01/
>
>
> ---------------------------------------------------------------------
> To unsubscribe, e-mail: amayausers-unsubscribe@xxxxxxxxxxxxxxxx
> For additional commands, e-mail: amayausers-help@xxxxxxxxxxxxxxxx
>



---------------------------------------------------------------------
To unsubscribe, e-mail: amayausers-unsubscribe@xxxxxxxxxxxxxxxx
For additional commands, e-mail: amayausers-help@xxxxxxxxxxxxxxxx

Other related posts: