I have the OS 7.00.055 and the under the "Thread Feed" tab I have the
following options/settings:
Column Feed: 40
Run/Fill Feed: 100
Material Thickness: 4
Autofeed Lower Limit: 1
Could someone please explain more about these settings and what they do
and what they should be.
I also have the Towa Bobbin Case Tension Gauge. The recommendation is
18-25. Does this sound right for the XT's? What does everyone find works
best for ARC poly in the XT?
Geri
----- Original Message -----
From: Loyda
To: amayausers@xxxxxxxxxxxxx
Sent: Friday, September 14, 2007 10:21 AM
Subject: [amayausers.com] Re: Acti-feed question - setting lower limits
Hi there,
I bought my AMAYA about 1 1/2 years ago. I have version 7.00.055 and I do
not have the lower actifeed minimum. I just have a setting for material
thickness, but not for a minimum. When you find out the version, I would
appreciate knowing it. Thanks!
-Loyda
----- Original Message -----
From: Shuffletown Embroidery
To: amayausers@xxxxxxxxxxxxx
Sent: Friday, September 14, 2007 4:14 AM
Subject: [amayausers.com] Re: Acti-feed question - setting lower limits
Thanks Aaron, I will call him today. I looked for information and did not
see anything on the Melco support website. The latest release shown on the
Amaya Users website is 7.00.055, so that's probably it.
Mary
Mary Buckle
Shuffletown Embroidery
Charlotte, NC
704-398-1273
From: amayausers-bounce@xxxxxxxxxxxxx
[mailto:amayausers-bounce@xxxxxxxxxxxxx] On Behalf Of Linen Barn
Sent: Thursday, September 13, 2007 6:25 PM
To: amayausers@xxxxxxxxxxxxx
Subject: [amayausers.com] Re: Acti-feed question - setting lower limits
In AMAYA OS click on settings. Select the Thread Feed Tab. At the bottom
is a box for Autofeed Lower Limit I think is what it says. As far as
version I can't remember which version it came out in. I am a Beta tester
so I get stuff early to work out bugs so I have had this feature for a
while now so its hard to remember when it came out but I am thinking it
was 7.055 but don't quote me on this. I am now running 7.00.110 and I am
not sure if this is a realeased version or not but I think it may be. If
nothing else call your sales rep and see if you are eligible for the free
upgrade or if you are past and have to pay. Its worth a shot.
Aaron Sargent
The Linen Barn
linen@xxxxxxxxxxx
541-770-2957
Medford, OR
----- Original Message -----
From: Shuffletown Embroidery
To: amayausers@xxxxxxxxxxxxx
Sent: Thursday, September 13, 2007 3:01 PM
Subject: [amayausers.com] Acti-feed question - setting lower limits
I can't believe I sent this question with the wrong subject. Here it is
again. (see attached.)
Since I can't find anything in my help section, I must not have the
correct version of the software. I'm at 7.00.047.
Mary
Mary Buckle
Shuffletown Embroidery
Charlotte, NC
704-398-1273
From: amayausers-bounce@xxxxxxxxxxxxx
[mailto:amayausers-bounce@xxxxxxxxxxxxx] On Behalf Of Shuffletown
Embroidery
Sent: Thursday, September 13, 2007 4:22 PM
To: amayausers@xxxxxxxxxxxxx
Subject: [amayausers.com] Re: Looking for camo (youth) in maroon, grey and
white
Hi everyone,
I was looking in the archives for the discussion about setting the lower
limit on acti-feed and haven't found it. Perhaps the discussion wasn't on
the board.
Could someone repost where that setting is and which software version?
Thanks,
Mary
Mary Buckle
Shuffletown Embroidery
Charlotte, NC
704-398-1273
===========================================================
The AmayaUsers Mailing List
Website: http://www.amayausers.com
Discussion Board: http://www.amayausers.com/boards
Subscribe/Unsubscribe: http://www.amayausers.com/list
===========================================================
--
No virus found in this incoming message.
Checked by AVG Free Edition. Version: 7.5.487 / Virus Database:
269.13.18/1007 - Release Date: 9/13/2007 9:48 PM
