|
[si-list]
||
[Date Prev]
[12-2003 Date Index]
[Date Next]
||
[Thread Prev]
[12-2003 Thread Index]
[Thread Next]
[SI-LIST] Re: XTK simulation
- From: "Hans Klos" <Hans.Klos@xxxxxxxxxx>
- To: <BRanjul@xxxxxxxxxxxxxx>, <si-list@xxxxxxxxxxxxx>
- Date: Tue, 2 Dec 2003 16:34:08 +0100
Ranju,
The message you see in the log file is OK.
It recognize the four layers, you specified
in the *.gcf file.
It should also generate a *.qnf and a *.isf file.
For investigation, you can open the *.isf file in
a isfviewer (supplied with the XTK software).
Best Regards,
Hans Klos
_______________________________________________
Sintecs BV, The EDA consulting provider
Hoofdweg 95
7676 AC Westerhaar
The Netherlands
tel. (031) 546-659015 http://www.sintecs.nl
fax. (031) 546-659013 mailto:Hans.Klos@xxxxxxxxxx
_______________________________________________
-----Oorspronkelijk bericht-----
Van: si-list-bounce@xxxxxxxxxxxxx
[mailto:si-list-bounce@xxxxxxxxxxxxx]Namens BRanjul@xxxxxxxxxxxxxx
Verzonden: maandag 1 december 2003 16:07
Aan: si-list@xxxxxxxxxxxxx
Onderwerp: [SI-LIST] XTK simulation
Dear all,
This is regarding XTK simulation.
The stack details added in the GCF file is given below which is generated
by axxxx -stack_gen <gcf file>
# ------------------------------------------------------------------------
# GCF STACK Section
# Generated by AXXX version Version 2.1.9 on Sat Sep 20 16:34:19 2003
# ------------------------------------------------------------------------
STACK
LAYER (0) = SIGNAL ( NAME = TOP, THICKNESS = 2.000000, DIELECTRIC =
1.000000 )
INSULATOR ( THICKNESS = 7.900000, DIELECTRIC = 4.500000 )
LAYER (1) = SIGNAL ( NAME = 3V3, THICKNESS = 1.400000, DIELECTRIC =
4.500000 )
INSULATOR ( THICKNESS = 6.000000, DIELECTRIC = 4.500000 )
LAYER (2) = PLANE ( NAME = GND, THICKNESS = 1.400000, DIELECTRIC =
4.500000 )
INSULATOR ( THICKNESS = 7.900000, DIELECTRIC = 4.500000 )
LAYER (3) = SIGNAL ( NAME = BOTTOM, THICKNESS = 2.000000, DIELECTRIC
= 1.000000 )
END_STACK
When I execute axxx <gcf file > ie with the gcf file
containing the above stack details, axxxx.log file gives the following
message in it.
Layer Stackup (Information only):
Layer count = 4
Default Connection Map = 1101
LAYER (0) = SIGNAL ( NAME = "TOP" )
INSULATOR = ( )
LAYER (1) = SIGNAL ( NAME = "3V3" )
INSULATOR = ( )
LAYER (2) = PLANE ( NAME = "GND" )
INSULATOR = ( )
LAYER (3) = SIGNAL ( NAME = "BOTTOM" )
Is this response OK? Or any of the parameters in GCF will be reflected in
the log?
Pleas help
Thanks in advance
Ranju
------------------------------------------------------------------
To unsubscribe from si-list:
si-list-request@xxxxxxxxxxxxx with 'unsubscribe' in the Subject field
or to administer your membership from a web page, go to:
http://www.freelists.org/webpage/si-list
For help:
si-list-request@xxxxxxxxxxxxx with 'help' in the Subject field
List technical documents are available at:
http://www.si-list.org
List archives are viewable at:
http://www.freelists.org/archives/si-list
or at our remote archives:
http://groups.yahoo.com/group/si-list/messages
Old (prior to June 6, 2001) list archives are viewable at:
http://www.qsl.net/wb6tpu
------------------------------------------------------------------
To unsubscribe from si-list:
si-list-request@xxxxxxxxxxxxx with 'unsubscribe' in the Subject field
or to administer your membership from a web page, go to:
http://www.freelists.org/webpage/si-list
For help:
si-list-request@xxxxxxxxxxxxx with 'help' in the Subject field
List technical documents are available at:
http://www.si-list.org
List archives are viewable at:
http://www.freelists.org/archives/si-list
or at our remote archives:
http://groups.yahoo.com/group/si-list/messages
Old (prior to June 6, 2001) list archives are viewable at:
http://www.qsl.net/wb6tpu
|
|
